- 您現在的位置：買賣IC網 > PDF目錄371415 > 27210 (Texas Instruments, Inc.) Li-Ion AND Li-Pol BATTERY GAS GAUGE IC FOR PORTABLE APPLICATIONS (bqJUNIOR) PDF資料下載
參數資料
| 型號： | 27210 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | Li-Ion AND Li-Pol BATTERY GAS GAUGE IC FOR PORTABLE APPLICATIONS (bqJUNIOR) |
| 中文描述： | 鋰離子和鋰聚合物電池電量監測計芯片的便攜式應用（bqJUNIOR） |
| 文件頁數： | 20/30頁 |
| 文件大?。?/td> | 337K |
| 代理商： | 27210 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
www.ti.com
Taper Current (TAPER) — Address 0x7B
This register contains the enable bit for the capacity aging estimate and the charge taper current value. The
taper current value, in addition to battery voltage, is used to determine when the battery has reached a full
charge state. The equation for programming the taper current is:
TAPER[6-0] = Design Taper Current (mA) * R
S
(m
) / 228 μV
where R
S
is the value of the sense resistor used in the system.
TAPER[7] should be set to
1
to enable the automatic aging of the LMD full capacity value when there are no
learning cycles. If this feature is enabled, LMD is reduced by Design Capacity / 1024 every time CYCL
increments by 2 and every time that a cumulative NAC self-discharge estimate reduction of 1.56% has been
made without charging the battery to full. If TAPER[7] is set to 0, there is no LMD reduction with cycle count or
self-discharge.
Pack Configuration (PKCFG) — Address 0x7C
bq27010, bq27210
SLUS707B–APRIL 2006–REVISED JANUARY 2007
BIT 7
GPIEN
BIT 6
QV1
BIT 5
QV0
BIT 4
BOFF(2)
BIT 3
BOFF(1)
BIT 2
BOFF(0)
BIT 1
DCFIX
BIT 0
TCFIX
NAME
GPIEN
Allows the pack manufacturer to set the state of the GPIO pin on initial power up. If the bit is 0, the
GPIEN bit is cleared on reset and the GPIO pin acts as a high-impedance output. If the bit is 1, the
GPIEN bit is set on reset and the GPIO pin acts as an input. The state of the GPIO pin can then be
read through the GPSTAT bit in the MODE register. If PKCFG is updated using the UPCFG host
command (see Device Control section), the updated PKCFG value will not reinitialize GPIEN in the
MODE register.
QV1 & QV0
These bits set the minimum qualification voltage for charge termination. The termination voltage
thresholds are set as listed in
Table 3
.
Table 3. Charge Termination Voltage Settings
QV1
0
0
1
1
QV0
0
1
0
1
Voltage (mV)
3968
4016
4064
4112
BOFF
These bits are used to store a typical board offset value for the gauge. This value is added to the
internal offset measurement and the total applied as an offset correction for the charge and
discharge coulometric measurements made by the DSCC. This is a 2s-complement signed number
with a value of 2.45 μV per bit.
Table 4. Board Offset Voltage Settings
Board Offset
7.35 μV
4.9 μV
2.45 μV
0
-2.45 μV
-4.9 μV
-7.35 μV
-9.8 μV
BOFF(2)
0
0
0
0
1
1
1
1
BOFF(1)
1
1
0
0
1
1
0
0
BOFF(0)
1
0
1
0
1
0
1
0
20
Submit Documentation Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| 270KD05JX | 11 to 460 Volts Varistor 0.7 to 29 Joule |
| 271KD05JX | 11 to 460 Volts Varistor 0.7 to 29 Joule |
| 270KD05NX | 4 to 460 Volts Varistor 0.20 to 22.5 Joule |
| 271KD05NX | 4 to 460 Volts Varistor 0.20 to 22.5 Joule |
| 270KD07NX | 4 to 510 Volts Varistor 0.8 to 47 Joule |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 27-210 | 制造商:Distributed By MCM 功能描述:Chassis Mount Female Solder-On BNC Connector 制造商:MCM 功能描述:RF/COAXIAL, BNC JACK, STRAIGHT, CRIMP; Connector Type:BNC Coaxial; Body Style:Straight Jack; Coaxial Termination:Crimp; Connector Mounting:Panel; Connector Type:BNC Coaxial |
| 272-100 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 272100-11 | 制造商:Amphenol Connex 功能描述:7/16 4HOLE PNL JK .141 LOW PIM - Bulk |
| 272-100-JBW | 制造商:RCD Components Inc 功能描述:Res Wirewound 10 Ohm 5% 10W ±20ppm/°C Molded AXL Thru-Hole Bulk |
| 272101 | 功能描述:RF 連接器 7/16 PANEL JACK .250 S/R 4 HOLE RoHS:否 制造商:Bomar Interconnect 產品:Connectors 射頻系列:BNC 型式:Jack (Female) 極性: 觸點電鍍:Gold 阻抗: 端接類型:Solder 主體類型:Straight Bulkhead 電纜類型: |
發布緊急采購，3分鐘左右您將得到回復。