- 您現在的位置：買賣IC網 > PDF目錄359939 > 24S15.3XT-I Analog IC PDF資料下載
參數資料
| 型號： | 24S15.3XT-I |
| 英文描述： | Analog IC |
| 中文描述： | 模擬IC |
| 文件頁數： | 5/8頁 |
| 文件大小： | 161K |
| 代理商： | 24S15.3XT-I |
45 Watt XT Single Series DC/DC Converters
2401 Stanwell Drive Concord, California 94520 Ph: 925/687-4411 or 800/542-3355 Fax: 925/687-3333 www.calex.com Email: sales@calex.com
5
3/2001
Remote Sense
The XT single features provisions for remote sense
connections. These allow the power supply to correct for line
drops of up to 0.6 volts per side. The remote sense connections
should be made with twisted pair wire or closely coupled PCB
traces. If the remote sense is not to be used these pins must
be connected to their respective output pins for proper output
voltage accuracy and regulation. There is approximately 2 mA
of current flowing in the remote sense lines.
Care should be taken to not disconnect the output pins
before the remote sense pins while the converter is in operation.
If this happens the output load current will run down the sense
leads possibly causing an output overvoltage condition. If the
unit must be
“
Hot Plugged
”
in the intended application, provision
should be made to disconnect the sense leads before the
power leads, disconnect the input power first or use the
remote ON/OFF to stop the converters operation.
Another option is to attach two 1N4001 diodes from pins 6
to 3 and pins 7 to 5 as shown in figure 3. These diodes will
shunt any current through the 10 ohm internal resistors
connected between the outputs and their respective outputs
when the voltage drop across the resistors exceeds
approximately 0.6 volts. This will limit momentary overvoltages
to about 1.2 volts during a hot plug-in.
Output Trimming
The trim pin may be used to adjust the outputs by up to ±10
% from the nominal factory setting. The trim may be used to
adjust for system wiring voltage drops or to adjust the +5
output up to 5.2 volts for ECL applications. Figure 4 shows the
proper connections to use the trim pin. If output trimming is not
desired the trim pin may be safely left floating.
Trimming the output up reduces the output current
proportionally to keep the maximum power constant. Output
current is not increased over the listed maximum when
trimming the output voltage down.
Figure 4.
The output can be trimmed by either a trimpot or fixed resistors. If
fixed resistors are used their values may range from 0 to infinite
ohms. The trimpot should be 10k ohms for 3.3 and 5 volt outputs or
20k ohms for 12 and 15 volt outputs.
Non Standard Output Voltages
The 12 and 15 volt XT
’
s will typically trim much lower than the
-10% specified. This allows the 12 and 15 volt XT
’
s to be
trimmed lower than specified for RF or other special
applications.
The 12 volt XT
’
s can be typically trimmed over a range of
8.6 to 13.3 volts. The 15 volt XT
’
s can be typically trimmed
over a range of 9.8 to 16.8 volts.
Down trim actually can reduce the minimum input voltage
in some circuits. Full up trim may not be achievable at
minimum input voltage and full rated load.
The maximum current available does not increase from the
listed maximum under low trim conditions.
Ultra Low Noise Output Circuit
The circuit shown in figure 5 can be used to reduce the output
noise to below 10 mV P-P over a 20 MHz bandwidth. Size
inductor L1 appropriately for the maximum expected load
current. The remote sense lines should be looped back
directly to the output pins to prevent feedback loop oscillation
due to the filters extra phase shift.
Figure 5.
For very low noise applications this circuit will reduce the output
noise to less than 10 mV P-P over a 0-20 MHz bandwidth. Be sure
to size the inductor appropriately for the maximum expected load
current.
Operation With Light Loads
At output loads less than specified minimum, the XT single will
operate in a
“
Burst Mode
”
. That is the XT will cease PWM
operation and instead operate in more of a burst mode. This
mode significantly reduces the light load input current to the
XT single. Under these conditions the output of the XT will
contain a larger than normal (compared to full load) output
noise, but at a lower frequency.
If this is a problem in your application the XT single may be
used with a dummy load resistor to keep the static output
current above the specified mimimum load.
相關PDF資料 |
PDF描述 |
|---|---|
| 24S15.800 | SMPS Controller |
| 24S24.2HE-N | Analog IC |
| 48S12.1000 | Dual/Triple Ultra-Low-Voltage SOT23 µP Supervisory Circuits |
| 48S12.4HE-N | Dual/Triple Ultra-Low-Voltage SOT23 µP Supervisory Circuits |
| 48S12.4XT | Dual/Triple Ultra-Low-Voltage SOT23 µP Supervisory Circuits |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 24S168 | 制造商:Thordarson 功能描述:Audio Transformer 1000Vrms 630Ohm Prim. DCR 0.82Ohm Sec. DCR |
| 24S175 | 制造商:LEADERTECH INC 功能描述:CBS Style Board Shields, CBS Shield Formed Unassembled 24S175 |
| 24S180 | 制造商:CANDD 制造商全稱:C&D Technologies 功能描述:Bobbin Wound Surface Mount Inductors |
| 24S180C | 功能描述:固定電感器 Shielded18uH1.22A RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
| 24S1R5.1200HW | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。