- 您現在的位置：買賣IC網 > PDF目錄371390 > 24AA1025 (Microchip Technology Inc.) 1024K I2C⑩ CMOS Serial EEPROM PDF資料下載
參數資料
| 型號： | 24AA1025 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 1024K I2C⑩ CMOS Serial EEPROM |
| 中文描述： | 1024K的I2C⑩的CMOS串行EEPROM |
| 文件頁數： | 7/22頁 |
| 文件大?。?/td> | 267K |
| 代理商： | 24AA1025 |
2007 Microchip Technology Inc.
Preliminary
DS21941E-page 7
24AA1025/24LC1025/24FC1025
5.0
DEVICE ADDRESSING
A control byte is the first byte received following the
Start condition from the master device (Figure 5-1).
The control byte consists of a 4-bit control code; for the
24XX1025, this is set as ‘
1010
’ binary for read and
write operations. The next bit of the control byte is the
block select bit (B0). This bit acts as the A16 address
bit for accessing the entire array. The next two bits of
the control byte are the Chip Select bits (A1, A0). The
Chip Select bits allow the use of up to four 24XX1025
devices on the same bus and are used to select which
device is accessed. The Chip Select bits in the control
byte must correspond to the logic levels on the corre-
sponding A1 and A0 pins for the device to respond.
These bits are in effect the two Most Significant bits of
the word address.
The last bit of the control byte defines the operation to
be performed. When set to a one, a read operation is
selected, and when set to a zero, a write operation is
selected. The next two bytes received define the
address of the first data byte (Figure 5-2). The upper
address bits are transferred first, followed by the Less
Significant bits.
Following the Start condition, the 24XX1025 monitors
the SDA bus checking the device type identifier being
transmitted. Upon receiving a ‘
1010
’ code and appro-
priate device select bits, the slave device outputs an
Acknowledge signal on the SDA line. Depending on the
state of the R/W bit, the 24XX1025 will select a read or
write operation.
This device has an internal addressing boundary
limitation that is divided into two segments of 512K bits.
Block select bit ‘B0’ to control access to each segment.
FIGURE 5-1:
CONTROL BYTE
FORMAT
5.1
Contiguous Addressing Across
Multiple Devices
The Chip Select bits A1, A0 can be used to expand the
contiguous address space for up to 4 Mbit by adding up
to four 24XX1025’s on the same bus. In this case,
software can use A0 of the control byte as address bit
A16 and A1 as address bit A17. It is not possible to
sequentially read across device boundaries.
Each device has internal addressing boundary
limitations. This divides each part into two segments of
512K bits. The block select bit ‘B0’ controls access to
each “half”.
Sequential read operations are limited to 512K blocks.
To read through four devices on the same bus, eight
random Read commands must be given.
FIGURE 5-2:
ADDRESS SEQUENCE BIT ASSIGNMENTS
1
0
1
0
B0
A1
A0
S
ACK
R/W
Control Code
Chip
Select
Bits
Slave Address
Acknowledge Bit
Start Bit
Read/Write Bit
Block
Select
Bits
1
0
1
0
B
0
A
1
A
A
11
A
10
A
9
A
7
A
0
A
8
A
12
Control Byte
Address High Byte
Address Low Byte
Control
Code
Chip
Select
Bits
X = “don’t care” bit
A
13
A
14
Block
Select
Bit
A
15
相關PDF資料 |
PDF描述 |
|---|---|
| 24AA128T-ESN | I2C⑩ Serial EEPROM Family Data Sheet |
| 24AA128-EMC | I2C⑩ Serial EEPROM Family Data Sheet |
| 24AA128-EMF | I2C⑩ Serial EEPROM Family Data Sheet |
| 24AA128-EMS | I2C⑩ Serial EEPROM Family Data Sheet |
| 24AA128-EOT | I2C⑩ Serial EEPROM Family Data Sheet |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 24AA1025_08 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1024K I2C? CMOS Serial EEPROM |
| 24AA1025_11 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1024K I2C? CMOS Serial EEPROM |
| 24AA1025_12 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1024K I2Ca?￠ Serial EEPROM |
| 24AA1025-E/P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1024K I2C? CMOS Serial EEPROM |
| 24AA1025-E/SM | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1024K I2C? CMOS Serial EEPROM |
發布緊急采購，3分鐘左右您將得到回復。