
15
AMP M Series
Pin and Socket Connectors
Catalog 82003
Dimensions are in millimeters
Dimensions are shown for
USA: 1-800-522-6752
South America: 55-11-3611-1514
Revised 06-08
and inches unless otherwise
reference purposes only.
Canada: 1-905-470-4425
Hong Kong: 852-2735-1628
specified. Values in brackets are
Specifications subject
Mexico: 01-800-733-8926
Japan: 81-44-844-8013
www.tycoelectronics.com
equivalent U.S. Customary Units.
to change.
C. America: 52-55-5-729-0425
UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Number of Positions
41
50
75
104
104 CF
160 CF
Component Description
202135-2
201358-1
—
Plug Block
201302-1
200277-2
—
Receptacle Block Phenolic
STANDARD
202135-4
201358-3
—
Plug Block
HOUSINGS
201302-3
200277-4
—
Receptacle Block Diallyl Phthalate
Pages 44 to 51
—
1-201692-6
—
Plug Block
—
Receptacle Block Polyester
—
180° Two-
Al Anodized
—
Piece Long
Zinc Plated Steel
—
Al Anodized
—
180° Two-
Zinc Plated Steel
—
Piece Short
Zinc Plated Cast Al
—
90° Two-Piece Long
SHIELDS
—
90° Two-Piece Short
Pages 84 to 87
—
45° Two-Piece Short
Nickel
—
45° Two-Piece Deep
Plated
—
180° One-Piece Long
Steel
—
180° One-Piece Short
201486-2
201470-2
—
90° One-Piece Short
200389-2
—
Center Male
GUIDE
200390-2
—
Center Female
HARDWARE
—
1-200833-1
—
Corner Male
Stainless Steel
Page 81
—
1-200835-1
—
Corner Female
201921-1
201925-1
—
Male—Nickel Plated Spring Steel
LOCKING SPRINGS1
201922-1
201926-1
—
Female—Stainless Steel
Page 80
—
Internal Open End
Nickel Plated Steel
—
Internal Closed End
Nickel Plated Steel
PIN HOODS
—
External Closed End Al Iridite
Pages 82 and 83
—
External Closed End Nickel Plated Steel
Cable-to-Cable (Continued)
1.
Confirm that Application C (at left) most closely meets
your requirements. (Other applications are shown on
pages 10-13 and 16 through 25.)
required.
3. Select part numbers required for the application listed
in the column below the number of positions.
If a part number is not listed for a particular item, it is
not available.
If more than one part number is listed for a particular
hardware item, choose the one which best fits your appli-
cation.
4. Dimensional information is available on the indicated
pages under description column.
5. Select Contacts: Type II (page 30), Type III+ (pages 31
through 35) or Subminiature Coaxial (pages 40, 41).
Special application housings may be substituted
for these standard housings. See Special Application
Section.
This cable-to-cable application utilizes locking springs,
one-piece shields, a pin hood for pin protection and guide
hardware. The shields are available with both 180° and 90°
cable exits. The 180° shields are available in a long version
which provides pin protection in lieu of a pin hood.
A short shield and a pin hood or a long shield can be used on
one side only of a mated pair of connectors. The mating con-
nector must use a short shield.
The 34 and 50 position connectors can be used with either
center or corner guide hardware. If center guides are used, an
additional four 4-40 screws are required to secure the locking
springs. If corner guides are used, an additional two 4-40
screws will be required to attach the shield. Corner guides
require four guide pins and four guide sockets for each mated
pair of connectors.
}
C
onnect
or
/Har
dw
ar
e
Selection
Guide