- 您現在的位置：買賣IC網 > PDF目錄1887 > 20-101-0788 (Rabbit Semiconductor)COMPUTER SGL-BOARD OP6600 W/SRAM PDF資料下載
參數資料
| 型號： | 20-101-0788 |
| 廠商： | Rabbit Semiconductor |
| 文件頁數： | 24/90頁 |
| 文件大小： | 0K |
| 描述： | COMPUTER SGL-BOARD OP6600 W/SRAM |
| 標準包裝： | 1 |
| 系列： | SBC |
| 模塊/板類型： | 單板計算機模塊 |
| 適用于相關產品： | OP6600 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁
26
Intellicom (OP6600/OP6700)
3.2.3 Programming Port
The Intellicom has a 10-pin programming header labeled J4. The programming port uses
the Rabbit 2000’s serial port A for communication. The programming port uses the Rabbit
2000’s Serial Port A for communication. Dynamic C uses the programming port to down-
load and debug programs.
The programming port is also used for the following operations.
Cold-boot the Rabbit 2000 on the Intellicom after a reset.
Remotely download and debug a program over an Ethernet connection using the
RabbitLink EG2110.
Fast copy designated portions of flash memory from one Rabbit-based board (the
master) to another (the slave) using the Rabbit Cloning Board.
Alternate Uses of the Programming Port
All three clocked Serial Port A signals are available as
a synchronous serial port
an asynchronous serial port, with the clock line usable as a general CMOS input
The programming port may also be used as a serial port via the DIAG connector on the
programming cable.
In addition to Serial Port A, the Rabbit 2000 startup-mode (SMODE0, SMODE1), status,
and reset pins are available on the programming port header.
The two startup mode pins determine what happens after a reset—the Rabbit 2000 is
either cold-booted or the program begins executing at address 0x0000.
The status pin is used by Dynamic C to determine whether a Rabbit microprocessor is
present. The status output has three different programmable functions:
1. It can be driven low on the first op code fetch cycle.
2. It can be driven low during an interrupt acknowledge cycle.
3. It can also serve as a general-purpose output.
The /RESET_IN pin is an external input that is used to reset the Rabbit 2000 and the Intel-
licom onboard peripheral circuits.
Refer to the Rabbit 2000 Microprocessor User’s Manual for more information.
相關PDF資料 |
PDF描述 |
|---|---|
| 20-101-1068 | MODULE RABBITCORE RCM3315 |
| 20-101-1131 | MODULE RCM4200 RABBITCORE |
| 20-101-1139 | RCM4310 RABBITCORE |
| 20-101-1154 | MODULE RCM4120 RABBITCORE |
| 20-101-1197 | MODULE RABBITCORE RCM3910 ROHS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 201-0108-01 | 功能描述:印刷電路板和試驗板 RJ11/45 and USB Connector RoHS:否 制造商:3M Electronic Solutions Division 產品:Jumper & Insulated Wires 描述/功能:Jumper wire, 22 AWG 0.1 inch 長度:0.1 in 寬度: |
| 20-101-0818 | 功能描述:單板計算機 BL2100 Fric Lk 512K RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm |
| 20-101-0820 | 功能描述:COMPUTER SGL-BD BL2000 SRAM/FLSH RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器或微處理器模塊 系列:SBC 產品目錄繪圖:DLP-245SY-G 標準包裝:1 系列:USB 模塊/板類型:開發(fā)板 適用于相關產品:USB 其它名稱:813-1006 |
| 20-101-0841 | 功能描述:模塊化系統(tǒng) - SOM BL2000 FRICT LOCK W/ RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| 20-101-0847 | 功能描述:模塊化系統(tǒng) - SOM BL2121 LOCK RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
發(fā)布緊急采購，3分鐘左右您將得到回復。