參數資料
型號: 20-101-0453
廠商: Rabbit Semiconductor
文件頁數: 4/30頁
文件大?。?/td> 0K
描述: MODULE RABBITCORE RCM2300
標準包裝: 1
系列: RabbitCore®
模塊/板類型: MPU 核心模塊
適用于相關產品: RCM2300
產品目錄頁面: 620 (CN2011-ZH PDF)
其它名稱: 316-1089
8
RabbitCore RCM2300
2.2.2 Prototyping Board Expansion
The Prototyping Board comes with several unpopulated areas, which may be filled with
components to suit the user’s development needs. After you have experimented with the
sample programs in Section 3.5, you may wish to expand the Prototyping Board’s capabil-
ities for further experimentation and development. Refer to the Prototyping Board sche-
matic (090–0122) for details as necessary.
Module Extension Headers
—The complete pin set of both the master and slave mod-
ules is duplicated at these two sets of headers. Developers can solder wires directly into
the appropriate holes, or, for more flexible development, 0.1" pitch 26-pin header strips
can be soldered into place. See Figure 1 for the header pinouts.
RS-232
—Two 2-wire or one 5-wire RS-232 serial port can be added to the Prototyping
Board by installing an RS-232 driver IC and four capacitors. The Maxim MAX232CPE
driver chip or a similar device is recommended for U2. Refer to the Prototyping Board
schematic for additional details.
A 10-pin 0.1-inch spacing header strip can be installed at J6 to permit connection of a
ribbon cable leading to a standard DE-9 serial connector.
All RS-232 port components mount to the top side of the Prototyping Board below and
to the left of the MASTER module position.
NOTE: The RS-232 chip, capacitors and header strip are available from electronics dis-
tributors such as Digi-Key.
Prototyping Board Component Header
—Four I/O pins from the RCM2300 module
are hard-wired to the Prototyping Board LEDs and switches through JP1 on the under-
side of the Prototyping Board.
To disconnect these devices and permit
the pins to be used for other purposes, cut
the traces between the pin rows of JP1.
Use a knife or similar tool to cut or break
the traces crossing JP1 in the area
between the silk-screened arrows, as
indicated in Figure 3.
Use jumpers across the positions on
JP1 if you need to reconnect any of the
devices later on.
Figure 3. Prototyping Board Header JP1
(located on BOTTOM SIDE of board)
Cut
PE1 PE7 PB2 PB3
JP1
DS2 DS3 S2 S3
相關PDF資料
PDF描述
20-101-1235 CORE MODULE RCM5700
11FMN-BMTTR-A-TB CONN FMN HSNG 11POS STAG REV SMD
046232103103800+ CONN FFC/FPC 3POS 1MM R/A SMD
15FE-ST-VK-N CONN FFC 15POS RA 1.25MM
09FMN-BMTR-A-TB CONN FMN HOUSNG 9POS SGL REV SMD
相關代理商/技術參數
參數描述
20-101-0454 功能描述:模塊化系統 - SOM RCM2200 RABBITCORE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-0455 功能描述:單板計算機 BL2010 RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm
20-101-0456 功能描述:單板計算機 BL2020 RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm
20-101-0457 功能描述:單板計算機 BL2030 Board RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm
20-101-0461 功能描述:單板計算機 BL2100 RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm