參數資料
型號: 20-101-0303
廠商: Rabbit Semiconductor
文件頁數: 110/126頁
文件大?。?/td> 0K
描述: SMARTSCREEN OP7100 W/TOUCHSCREEN
標準包裝: 1
顯示器類型: STN - 超扭轉向列,帶觸摸面板
可視范圍: 121.00mm L x 91.00mm W
背光: CCFL - 白
點象素: 320 x 240(QVGA)
接口: 串行
點間距: 0.36mm x 0.36mm
產品目錄頁面: 618 (CN2011-ZH PDF)
其它名稱: 20-101-0303-ND
20-101-303
20-101-303-ND
316-1175
OP7100
84
Installation
Grounding
Many of the OP7100 ICs are sensitive to static. Use extra
caution when handling units in high-static areas.
To meet electromagnetic compatibility requirements, and in particular to
prevent misoperation or damage from electrostatic discharges, the bezel
must be connected to a protective ground via a low-impedance path.
A protective building ground is recommended once the OP7100 is installed
at the location where it will be used. In addition to providing protection
against an unexpected electric shock, the connection to building ground
also mitigates any problems from external electrostatic discharges and
transients, and dampens any RF emissions.
The metal casing is already connected electrically to the bezel, and so does
not require a separate ground connection. The connection to the building
ground should always be made through the bezel.
The recommended way to connect an OP7100 to a building ground is to
mount the unit in a metal panel that is already grounded. Ensure that the
areas around the securing nuts are clean and free from corrosion or other
contaminants so that a good electrical connection can be realized.
Alternatively, use a wire with a size of at least 20AWG (0.5 mm2), prefer-
ably stranded, to establish a connection between one of the bezel mounting
studs and the protective building ground. This wire should be as short as
possible to keep its impedance low.
There is an electrical connection between the OP7100 bezel/casing and the
connection marked GND on the power supply header, J11, via a jumper on
header JP5. This connection is also the return for the DC power supply and
the I/O signals, and should not be relied on for a protective ground
connection.
Remove the jumper across JP5 if you wish to isolate the OP7100 bezel/
casing ground from the power supply ground. Any common-mode voltage
between signal ground and protective ground should be kept below 40 V DC.
相關PDF資料
PDF描述
TPSW107M004R0100 CAP TANT 100UF 4V 20% 2312
GLK24064-25-VPT LCD GRAPHIC DISPL 240X64 Y/G BK
MK-GT380N KIT MODULE 3.8" MONOCHROME DISP
MK-GT380T KIT MODULE 3.8" TRANSFLECTV DISP
CWX823-060.0M OSC 60.0000MHZ 3.3V +-50PPM SMD
相關代理商/技術參數
參數描述
20-101-0343 功能描述:電纜組件 BL1800 proto board RoHS:否 制造商:Molex 產品:Power Assemblies 類型:Cable Assembly 連接器端口 A:No Connector 連接器端口 A 管腳計數:4 連接器端口 B:No Connector 連接器端口 B 管腳計數: 型式:Male 線規 - 美國線規(AWG):20, 28 長度:0.305 m 顏色:Black, Red
20-101-0356 功能描述:單板計算機 BL1800 RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm
20-101-0357 功能描述:單板計算機 BL1810 SINGLE BOARD COMPUTER RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm
20-101-0358 功能描述:單板計算機 BL1820 RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm
20-101-0383 功能描述:模塊化系統 - SOM RCM2020 RabbitCore RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in