- 您現在的位置：買賣IC網 > PDF目錄366091 > 16235XXF (Electronic Theatre Controls, Inc.) AM29LV641DL-90REI PDF資料下載
參數資料
| 型號： | 16235XXF |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | AM29LV641DL-90REI |
| 中文描述： | 太平洋顯示器件 |
| 文件頁數： | 15/17頁 |
| 文件大小： | 256K |
| 代理商： | 16235XXF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁
SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY MODULE
MODEL NO: 16235
5. PRECAUTIONS FOR USING LCD MODULES
Installing LCD Modules
The hole in the printed circuit board is used to fix LCM as shown in the picture below. Attend to the following items when
installing the LCM.
1)
Cover the surface with a transparent protective plate to protect the polarizer and LC cell.
PACIFIC DISPLAY DEVICES
07.01.2003
15
2)
When assembling the LCM into other equipment, the spacer to the bit between the LCM and the fitting plate
should have enough height to avoid causing stress to the module surface, refer to the individual specifications for
measurements. The measurement tolerance should be
±
0.1mm.
Precaution for Handing LCD Modules
Since LCM has been assembled and adjusted with a high degree of precision, avoid applying excessive shocks to the module or
making any alterations or modifications to it.
1)
Cover the surface with a transparent protective plate to protect the polarizer and LC cell.
2)
Do not alter, modify or change the shape of the tab on the metal frame.
3)
Do not make extra holes on the printed circuit board, modify its shape or change the positions of components to
be attached.
4)
Do not damage or modify the pattern writing on the printed circuit board.
5)
Absolutely do not modify the zebra rubber strip (conductive rubber) or heat seal connector.
6)
Except for soldering the interface, do not make any alterations or modifications with a soldering iron.
7)
Do not drop, bend or twist LCM.
Electro-Static Discharge Control
Since this module uses a CMOS LSI, the same careful attention should be paid to electrostatic discharge as for an ordinary
CMOS IC.
1)
Make certain that you are grounded when handing LCM.
2)
Before remove LCM from its packing case or incorporating it into a set, be sure the module and your body have
the same electric potential.
3)
When soldering the terminal of LCM, make certain the AC power source for the soldering iron does not leak.
4)
When using an electric screwdriver to attach LCM, the screwdriver should be of ground potentiality to minimize
as much as possible any transmission of electromagnetic waves produced sparks coming from the commutator of
the motor.
5)
As far as possible make the electric potential of your work clothes and that of the work bench the ground
potential.
6)
To reduce the generation of static electricity be careful that the air in the work is not too dried. A relative
humidity of 50%-60% is recommended.
Precaution for soldering to the LCM
1)
Observe the following when soldering lead wire, connector cable and etc. to the LCM.
a)
Soldering iron temperature : 280
°
C
±
10
°
C.
b)
Soldering time : 3-4 sec.
2)
Solder : eutectic solder.
相關PDF資料 |
PDF描述 |
|---|---|
| 16285 | HTSNK, C LONG. .4H LOW FLOW, THREADED |
| 16285-A | Slim Power Relay, 1 Form A, 6A 250VAC, Silver Alloy Contact |
| 16297 | Slim Power Relay, 1 Form A, 6A 250VAC, Silver Alloy Contact |
| 16297-A | Slim Power Relay, 1 Form A, 6A 250VAC, Silver Alloy Contact |
| 16299 | Slim Power Relay, 1 Form A, 6A 250VAC, Silver Alloy Contact |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 16236 | 功能描述:3M(TM) PPS(TM) SPRAY GUN HOLDER 制造商:3m 系列:PPS? 零件狀態:在售 配件類型:支座 配套使用產品/相關產品:噴漆槍 標準包裝:1 |
| 1623600-1 | 制造商:TE Connectivity 功能描述:CRG1206 5% 13R - Tape and Reel |
| 1623603 | 功能描述:CRIMP CONTACT TURNED CONTACT DIA 制造商:phoenix contact 系列:* 零件狀態:在售 標準包裝:100 |
| 1623603-2 | 功能描述:RES 15.0 OHM 1/4W 5% 1206 RoHS:是 類別:電阻器 >> 芯片電阻 - 表面安裝 系列:CRG, Neohm 標準包裝:500 系列:PHP 電阻（歐姆）:200 功率（瓦特）:2.5W 復合體:薄膜 特點:耐燃 溫度系數:±25ppm/°C 容差:±0.1% 封裝/外殼:2512（6432 公制） 尺寸/尺寸:0.259" L x 0.124" W（6.58mm x 3.15mm） 高度:0.033"（0.84mm） 端子數:2 包裝:帶卷 (TR) |
| 1623604 | 功能描述:CRIMP CONTACT TURNED CONTACT DIA 制造商:phoenix contact 系列:* 零件狀態:在售 標準包裝:100 |
發布緊急采購，3分鐘左右您將得到回復。