- 您現在的位置：買賣IC網 > PDF目錄7027 > 15005 (Desco)MAT 48"X40' CONDUCTIVE VINYL ROL PDF資料下載
參數資料
| 型號： | 15005 |
| 廠商： | Desco |
| 文件頁數： | 2/4頁 |
| 文件大?。?/td> | 0K |
| 描述： | MAT 48"X40' CONDUCTIVE VINYL ROL |
| 其它有關文件： | Mat Selection Chart |
| MSDS 材料安全數據表： | StatFree® Conductive Vinyl MSDS |
| 標準包裝： | 1 |
| 系列： | STATFREE CV™ |
| 墊子類型： | 地板卷筒 |
| 形狀： | 矩形 |
| 長度： | 40'（12.19m） |
| 寬： | 4'（1.22m） |
| 厚度： | 0.13"（3.30mm） |
| 顏色： | 黑 |
| 材質： | 乙烯基 |
| 特點： | 導電 |
| 其它名稱： | Q1164346 |
TB-2000 Page 2 of 4
Grounding Methods
Method 1 (Grounding via ground cords)
1. Desco recommends using a common point ground cord when
grounding via ground cords. Most common point ground cords
will ground your ESD worksurface and provide banana jack
ground points for two wrist straps.
2. A common point ground should be installed at each workstation
and should be connected directly to a verified “green wire”
equipment ground. Only one groundable point should exist on a
worksurface.
Figure 5. Common point ground for each workstation.
3. Wrist straps should never be grounded through a worksurface,
as the added resistance of the worksurface material will
prevent the wrist strap from operating properly.
Figure 6. Proper grounding of wrist straps.
4. Per ANSI/ESD S1.1, a current limiting resistor in the wrist strap
ground cord is recommended. If other than a one megohm
resistor, special marking in red is required.
For additional information on grounding we recommend Desco
Technical Bulletin TB-2007.
Groundable Point Installation
1. Before installing a groundable point on your mat you must first
determine whether you will need a snap socket or stud, the
type of snap hardware and the location.
2. Desco has three types of 10mm (.395") field installable mat
grounding snaps. The first type is a screw-on snap kit Desco
item number 09864 Universal Snap Kit.
A. Determine the position of the grounding snap (one only
per mat) and type of fastener you will be installing (socket
or stud). Take precautions not to cut your hand, and punch
a hole through the material with a small Phillips screwdriver
or awl.
B. Remove the release paper from the circular common point
ground label and affix it so that it aligns with the hole on the
material.
C. Select one of the screws as follows:
Material less than .100" thick - short screw
Material greater than .100" thick - long screw
D. Insert the screw through the top on the snap stud or socket,
the washer, the label and the material. Affix the assembly
with the conical nut supplied with the kit and tighten down
the screw using a Phillips screwdriver.
E. Remaining will be either a 10mm stud or socket, and either
a long or short screw to be discarded or saved for another
application.
ASSEMBLE
SCREW, STUD,
WASHER, LABEL
AND CONICAL NUT
AS SHOWN
DESCO WEST
- 3651 Walnut Avenue, Chino, CA 91710 (909) 627-8178
DESCO EAST - One Colgate Way
, Canton, MA 02021-1407 (781) 821-8370 Web Site: Desco.com
WRONG!
RIGHT!
Figure 8. Installing Universal Snap Kit on mat.
USE A PHILLIPS
SCREWDRIVER OR
AWL TO PUNCH
A HOLE IN THE
MATERIAL
2012 DESCO INDUSTRIES INC.
Employee Owned
Figure 7. Three kinds of snaps.
3. The second type of mat grounding snap is the push and
clinch snap. This snap is designed for use with any type of
soft mat material: dissipative, conductive or multi-layered. It is
recommended for use with three-layered material, because it
provides excellent contact with the internal conductive scrim
layer. It is recommended that before inserting this snap, the
mat be punctured with a sharp tool where the snap will be
placed. Take precautions not to cut your hand. Push and Clinch
snaps are available as a snap stud as item #09861 and as a
snap socket as item #09863.
A. Remove the release paper from the circular label and
affix it onto the mat material in the desired location.
B. Center the prongs on the snap assembly with the label.
Apply pressure to the snap until the prongs come through
the back of the mat, then clinch over prongs to secure snap
as shown in Figure 9.
相關PDF資料 |
PDF描述 |
|---|---|
| 430311-26-0 | TERM BARRIER 26CIRC 1 ROW .4375 |
| 430211-26-0 | TERM BARRIER 26CIRC 1 ROW .4375 |
| CFTQ-7 | TERM BARRIER 7CIRC SGL ROW .375 |
| GBSX-20 | TERM BARRIER 20CIRC SGL ROW .438 |
| GFTPAX-12 | TERM BARRIER 12CIRC SGL ROW .438 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 15-005 | 制造商: 功能描述: 制造商:undefined 功能描述: 制造商:Jensen Tools 功能描述: 制造商:STANLEY 功能描述:REPLACEMENT BLADES FOR 15-333 制造商:Stanley Electric Co 功能描述:REPLACEMENT BLADES FOR 15-333 |
| 150-05 | 制造商:Coilcraft Inc 功能描述:NOT RoHS. RF inductor, no core (add 'L' for compliant version) |
| 1500-5 | 制造商:Brady Corporation 功能描述: |
| 15-005.25-157 | 制造商:Aries Electronics Inc 功能描述:CABLE 15POS .100 JUMPER 5.25 INC |
| 15-005.5-157 | 功能描述:多配對電纜 IN LINE JUMPERS DOUBLE END 15 COND RoHS:否 制造商:Belden Wire & Cable 線規 - 美國線規（AWG）:18 對數:1 絞合:16 x 30 屏蔽:Shielded 長度:1000 ft 電壓額定值:300 V 外殼材料:Polyvinyl Chloride (PVC) 絕緣材料:Polyethylene (PE) 類型:Audio, Control and Instrumentation 外殼顏色:Chrome |
發布緊急采購，3分鐘左右您將得到回復。