參數資料
型號： 1117-33
廠商： National Semiconductor Corporation
元件分類： 基準電壓源/電流源
英文描述： Micropower 5V, 100mA Low Dropout Linear Regulator
中文描述： 微5V的，100mA的低壓差線性穩壓器
文件頁數： 9/21頁
文件大?。?/td> 535K
代理商： 1117-33
Typical Performance Characteristics
(Continued)
LM1117-5.0 Line Transient Response
10091911
Application Note
1.0 External Capacitors/Stability
1.1 Input Bypass Capacitor
An input capacitor is recommended. A 10μF tantalum on the
input is a suitable input bypassing for almost all applications.
1.2 Adjust Terminal Bypass Capacitor
The adjust terminal can be bypassed to ground with a by-
pass capacitor (C
) to improve ripple rejection. This by-
pass capacitor prevents ripple from being amplified as the
output voltage is increased. At any ripple frequency, the
impedance of the C
should be less than R1 to prevent the
ripple from being amplified:
1/(2
π
*f
RIPPLE
*C
ADJ
)
<
R1
The R1 is the resistor between the output and the adjust pin.
Its value is normally in the range of 100-200
. For example,
with R1 = 124
and f
RIPPLE
= 120Hz, the C
ADJ
should be
>
11μF.
1.3 Output Capacitor
The output capacitor is critical in maintaining regulator sta-
bility, and must meet the required conditions for both mini-
mum amount of capacitance and ESR (Equivalent Series
Resistance). The minimum output capacitance required by
the LM1117 is 10μF, if a tantalum capacitor is used. Any
increase of the output capacitance will merely improve the
loop stability and transient response. The ESR of the output
capacitor should range between 0.3
- 22
. In the case of
the adjustable regulator, when the C
is used, a larger
output capacitance (22μf tantalum) is required.
2.0 Output Voltage
The LM1117 adjustable version develops a 1.25V reference
voltage, V
, between the output and the adjust terminal.
As shown in
Figure 1
, this voltage is applied across resistor
R1 to generate a constant current I1. The current I
from
the adjust terminal could introduce error to the output. But
since it is very small (60μA) compared with the I1 and very
constant with line and load changes, the error can be ig-
nored. The constant current I1 then flows through the output
set resistor R2 and sets the output voltage to the desired
level.
For fixed voltage devices, R1 and R2 are integrated inside
the devices.
3.0 Load Regulation
The LM1117 regulates the voltage that appears between its
output and ground pins, or between its output and adjust
pins. In some cases, line resistances can introduce errors to
the voltage across the load. To obtain the best load regula-
tion, a few precautions are needed.
Figure 2
, shows a typical application using a fixed output
regulator. The Rt1 and Rt2 are the line resistances. It is
obvious that the V
is less than the V
by the sum of
the voltage drops along the line resistances. In this case, the
load regulation seen at the R
would be degraded from
the data sheet specification. To improve this, the load should
be tied directly to the output terminal on the positive side and
directly tied to the ground terminal on the negative side.
10091917
FIGURE 1. Basic Adjustable Regulator
L
www.national.com
9
相關PDF資料
PDF描述
1117I50 Micropower 5V, 100mA Low Dropout Linear Regulator
1117IAD Micropower 5V, 100mA Low Dropout Linear Regulator
1117I-50 GIGATRUE 550 CAT PATCH CABLE NO BOOT 30FT GREEN
1117I-AD GIGATRUE 550 CAT PATCH CBL NO BOOT 30FT GR 25 PK
1117I33 GIGATRUE 550 CAT6 PATCH 4 FT, NON BOOT, RED
相關代理商/技術參數
參數描述
11-17-3349 功能描述:手工工具 CARRIER COVER 60627B111 RoHS:否 制造商:Molex 產品:Extraction Tools 類型: 描述/功能:Extraction tool
11-17-3443 功能描述:沖壓機與沖模 CONDUCTOR PUNCH RoHS:否 制造商:Souriau 大小: 產品:Dies 類型:Crimping 描述/功能:
11-17-3449 功能描述:沖壓機與沖模 CUT OFF PUNCH RoHS:否 制造商:Souriau 大小: 產品:Dies 類型:Crimping 描述/功能:
11-17-3453 功能描述:手工工具 WIRE CENTERING PIECE RoHS:否 制造商:Molex 產品:Extraction Tools 類型: 描述/功能:Extraction tool
11-17-3455 功能描述:沖壓機與沖模 FRONT CUT OFF DIE RoHS:否 制造商:Souriau 大小: 產品:Dies 類型:Crimping 描述/功能:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*