- 您現在的位置：買賣IC網 > PDF目錄366077 > 10TPB100ML (National Semiconductor Corporation) Hook-Up Wire; Conductor Size AWG:18; No. Strands x Strand Size:19 x 30; Jacket Color:Black; Approval Bodies:UL; Approval Categories:UL AWM Style 1371; Passes VW-1 Flame Test; Cable/Wire MIL SPEC:MIL-W-16878/4 Type E RoHS Compliant: Yes PDF資料下載
參數資料
| 型號： | 10TPB100ML |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Hook-Up Wire; Conductor Size AWG:18; No. Strands x Strand Size:19 x 30; Jacket Color:Black; Approval Bodies:UL; Approval Categories:UL AWM Style 1371; Passes VW-1 Flame Test; Cable/Wire MIL SPEC:MIL-W-16878/4 Type E RoHS Compliant: Yes |
| 中文描述： | N溝道場效應管同步降壓穩壓控制器輸出電壓低 |
| 文件頁數： | 2/22頁 |
| 文件大?。?/td> | 602K |
| 代理商： | 10TPB100ML |
Connection Diagram
20049411
14-Lead Plastic TSSOP
θ
= 155C/W
NS Package Number MTC14
Pin Description
BOOT (Pin 1)
- Supply rail for the N-channel MOSFET gate
drive. The voltage should be at least one gate threshold
above the regulator input voltage to properly turn on the
high-side N-FET.
LG (Pin 2)
- Gate drive for the low-side N-channel MOSFET.
This signal is interlocked with HG to avoid shoot-through
problems.
PGND (Pins 3, 13)
- Ground for FET drive circuitry. It should
be connected to system ground.
SGND (Pin 4)
- Ground for signal level circuitry. It should be
connected to system ground.
V
CC
(Pin 5)
- Supply rail for the controller.
PWGD (Pin 6)
- Power Good. This is an open drain output.
The pin is pulled low when the chip is in UVP, OVP, or UVLO
mode. During normal operation, this pin is connected to V
CC
or other voltage source through a pull-up resistor.
ISEN (Pin 7)
- Current limit threshold setting. This sources a
fixed 50μA current. A resistor of appropriate value should be
connected between this pin and the drain of the low-side
FET.
EAO (Pin 8)
- Output of the error amplifier. The voltage level
on this pin is compared with an internally generated ramp
signal to determine the duty cycle. This pin is necessary for
compensating the control loop.
SS (Pin 9)
- Soft start pin. A capacitor connected between
this pin and ground sets the speed at which the output
voltage ramps up. Larger capacitor value results in slower
output voltage ramp but also lower inrush current.
FB (Pin 10)
- This is the inverting input of the error amplifier,
which is used for sensing the output voltage and compen-
sating the control loop.
FREQ (Pin 11)
- The switching frequency is set by connect-
ing a resistor between this pin and ground.
SD (Pin 12)
- IC Logic Shutdown. When this pin is pulled low
the chip turns off the high side switch and turns on the low
side switch. While this pin is low, the IC will not start up. An
internal 20μA pull-up connects this pin to V
CC
.
HG (Pin 14)
- Gate drive for the high-side N-channel MOS-
FET. This signal is interlocked with LG to avoid shoot-
through problems.
L
www.national.com
2
相關PDF資料 |
PDF描述 |
|---|---|
| 10TQ040 | COG Technology, 128 x 64 pixel format |
| 10TQ040 | 10 AMP SCHOTTKY RECTIFIERS |
| 11016 | Isolated Resistor Termination Network |
| 110R1101X | THIN FILM RESISTOR SERIES |
| 1117-18 | Micropower 5V, 100mA Low Dropout Linear Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 10TPB100ML | 制造商:SANYO Semiconductor Co Ltd 功能描述:CAPACITOR 100UF 10V |
| 10TPB150ML | 功能描述:鉭質電容器-SMD聚合物 10volts 150uF ESR 40mohm RoHS:否 制造商:Kemet 電容:33 uF 電壓額定值:50 V ESR:40 mOhms 容差:20 % 工作溫度范圍: 外殼代碼 - in:2917 外殼代碼 - mm:7343 高度:4 mm 制造商庫存號:X Case 系列:T543 產品: 封裝:Reel |
| 10TPB220M | 功能描述:鉭質電容器-SMD聚合物 10volts 220uF ESR 40mohm RoHS:否 制造商:Kemet 電容:33 uF 電壓額定值:50 V ESR:40 mOhms 容差:20 % 工作溫度范圍: 外殼代碼 - in:2917 外殼代碼 - mm:7343 高度:4 mm 制造商庫存號:X Case 系列:T543 產品: 封裝:Reel |
| 10TPB220M | 制造商:SANYO Semiconductor Co Ltd 功能描述:CAPACITOR 220UF 10V |
| 10TPB220ML | 功能描述:鉭質電容器-SMD聚合物 10volts 220uF ESR 40mohm RoHS:否 制造商:Kemet 電容:33 uF 電壓額定值:50 V ESR:40 mOhms 容差:20 % 工作溫度范圍: 外殼代碼 - in:2917 外殼代碼 - mm:7343 高度:4 mm 制造商庫存號:X Case 系列:T543 產品: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。