參數資料
| 型號： | 10409 |
| 廠商： | Desco |
| 文件頁數： | 2/7頁 |
| 文件大?。?/td> | 0K |
| 描述： | PAINT COND LATEX GREY 5GAL |
| 標準包裝： | 1 |
| 系列： | Statguard® |
| 處理劑/清潔劑類型： | 涂料，導電 |
| 使用： | 地板 |
| 技術規(guī)格： | 灰 |
| 數量： | 5 加侖 |
| 包裝： | 桶 |
| 其它名稱： | 82002 |
Application
Always use in a well ventilated area or wear
a suitable respirator. Wear appropriate
eye protection such as splash goggles and
impervious type protection gloves to protect
hands.
MIXING
1. Mix paint thoroughly before use (See
Figure 2) using a 500-1500 RPM variable
speed drill and paint mixing attachment or a
paint mixer.
2. If the paint, after properly mixing, is not
freely transferring from the roller to the floor,
the Statguard ESD paint can be thinned with
water up to 10% max by volume.
a. Start by slowly mixing 5% water into the
master container and apply again.
b. Do not add more than 10% of water to
the mix.
APPLICATION BY ROLLER
1. Stir paint thoroughly to mix any
settled solids to produce uniform grey
color.
2. Combine separate cans of paint into
one container to ensure uniform color distribution. It is
recommended that a
test area be coated to ensure that the adhesion and electrical
performance
of the paint is acceptable. (See Adhesion Testing, Figure 5.) If the
test areas show inadequate adhesion, use an industrial
floor primer/sealer.
3. Saturate a 1/4” (6.35 mm) fine nap roller or an industrial brush
with paint. Remove
excess paint and trapped air from the applicator by moving
applicator several times in the paint tray.
4. A minimum number of strokes from
the applicator on the substrate is
recommended to minimize air bubbles.
APPLICATION BY SPRAY
Conventional Spray Gun: “E” fluid tip
and needle and #704, 765 or 78 air
gap.
Airless Spray: Spray gun and spray
cap or suitable orifice diameter
0.020-0.025” (0.508-0.635 mm).
Mix paint thoroughly before using
and stir occasionaly when applying.
No thinning necessary for spray
applications. Room temperature must be above 50°F (10°C).
A minimum of two coats of Statguard Conductive Acrylic Paint is
recommended for appropriate static protection.
TB-7001 Page 2 of 7
1.
Mix any settled solids to produce a
uniform grey color.
3.
Saturate a 1/4” fine nap roller with paint,
remove excess paint and trapped air.
2.
Combine separate cans into a larger
container.
4.
A minimum number of strokes from the
applicator is recommended.
Figure 2. Paint application with roller.
Figure 3. Spray paint
application
Clean Up
Wash applicators with water immediately after painting. Remove
paint spills promptly with a wet cloth. Close container after each
use. Keep container from freezing.
Drying Time
It is recommended that Statguard Conductive Acrylic Paint be
allowed to dry at a temperature in excess of 45°F (7°C) until dry.
A minimum of 1 to 2 hours drying time should be allowed before
applying the second coat. The finish can be applied after 48-72
hours or until the last coat of paint is cured. Wait a minimum of 12
hours drying time after the last coat before allowing light traffic on
the coated area. At high humidity levels, a longer drying time may
be necessary. Do not force dry.
Maintenance
Use sweeper, vacuum, or broom to remove dirt. Allow two weeks
drying time before using a damp mop to clean the coated area.
Do not use abrasive cleaners, floor rinse, or scrubbing machine to
clean the floor.
Finish/Sealer
Desco Statguard Conductive Acrylic Paint can be overcoated or
sealed with Statguard Floor Finish static dissipative coating to
increase durability, enhance shine, improve ease of maintenance,
and seal out dirt and debris. Desco Statguard Conductive Light
Grey Acrylic Paint needs the Statguard Floor Finish for gloss
and ease of maintenance . Statguard is a polymer base floor
finish/sealer that can be used as a top coat on the Conductive
Acrylic Paint. Surface resistivity will then be in the 10E6-10E7
ohms range. Two coats are recommended. Three coats will
improve electrical properties, durability and reduce frequency of
2011 DESCO INDUSTRIES INC.
Employee Owned
DESCO INDUSTRIES INC. 3651 Walnut Avenue, Chino, CA 91710 (909) 627-8178 Fax (909) 627-7449 Web Site: DescoIndustries.com
相關PDF資料 |
PDF描述 |
|---|---|
| 10415 | ANTISTATIC SPRAY REZTORE 1QT. |
| 10438 | CLEAN REZTORE SURFACE&MAT 2.5GAL |
| 10520 | FINISH FLOOR STATGUARD 55GAL |
| 10601 | WIPES ANTISTATC CAN OF 60, 12 CT |
| 12550 | FOAM HIGH DENSITY 3/4" 24X36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 10-409 | 制造商:STANLEY 功能描述:KNIFE 9MM 制造商:The Stanley Works 功能描述:KNIFE, 9MM 制造商:STANLEY 功能描述:KNIFE, 9MM; Knife Type:Snapoff; Blade Material:Stainless Steel; Blade Length:135mm; Blade Width:9mm ;RoHS Compliant: NA |
| 104090000 | 功能描述:Red, Green, Blue (RGB) LED Indication - Discrete 2.1V Red, 3.15V Green, 3.15V Blue Radial 制造商:seeed technology co., ltd 系列:- 包裝:散裝 零件狀態(tài):過期 顏色:紅，綠，藍（RGB） 透鏡顏色:無色 透鏡透明度:透明 毫燭光等級:350mcd 紅，1150mcd 綠，600mcd 藍 透鏡樣式/尺寸:- 電壓 - 正向（Vf）（典型值）:2.1V 紅，3.15V 綠，3.15V 藍 電流 - 測試:20mA 紅， 20mA 綠， 20mA 藍 視角:50° 安裝類型:通孔 波長 - 主:- 波長 - 峰值:625nm 紅，518nm 綠，466nm 藍 特性:- 封裝/外殼:徑向 供應商器件封裝:8mm 圓形 大小/尺寸:- 高度（最大值）:11.50mm 標準包裝:1 |
| 1040900000 | 制造商:Weidmuller 功能描述:CONN HEADER 22POS 3.81MM BLK R/A |
| 104090102103 | 制造商:Dialight 功能描述:LARGE OIL TIGHT PANEL IND. |
| 104-0901-02-103 | 功能描述:燈座與配件 OIL TIGHT PANEL IND RoHS:否 制造商:Chicago Miniature 產品:PMI Base 燈類型:Incandescent, Neon 燈大小:T-2, T-3 1/4 燈座類型:Miniature Bayonet 封裝:Bulk |
發(fā)布緊急采購，3分鐘左右您將得到回復。