and it is not referenced t" />
參數資料
型號： 101-1155
廠商： Rabbit Semiconductor
文件頁數： 78/134頁
文件大小： 0K
描述： KIT DEVELOPMENT USA RCM4200
標準包裝： 1
系列： RabbitCore 4000
類型： MPU 核心模塊
適用于相關產品： RCM4200
所含物品： RabbitCore 模塊、開發板、交流適配器、纜線和 Dynamic C? 光盤
其它名稱： 316-1126
42
RabbitCore RCM4200
If a device such as a battery is
connected across two channels
for a differential measurement,
and it is not referenced to
analog ground, then the current
from the device will flow
through both sets of attenuator
resistors without flowing back
to analog ground as shown in
Figure 11. This will generate a
negative voltage at one of the
inputs, LN1, which will almost
certainly lead to inaccurate A/D
conversions. To make such differential measurements, connect the R1 resistors to the A/D
converter’s internal reference voltage, which is software-configurable for 1.15 V, 2.048 V,
or 2.5 V. This internal reference voltage is available on pin 49 of header J2 as VREF, and
allows you to convert analog input voltages that are negative with respect to analog ground.
NOTE: The amplifier inside the A/D converter’s internal voltage reference circuit has a
very limited output-current capability. The internal buffer can source up to 20 mA and
sink only up to 200 A. Use a separate buffer amplifier if you need to supply any load
current.
The A/D converter’s CONVERT pin is available on pin 48 of header J2 and can be used as
a hardware means of forcing the A/D converter to start a conversion cycle at a specific time.
The CONVERT signal is an edge-triggered event and has a hold time of two CCLK periods
for debounce.
A conversion is started by an active (rising) edge on the CONVERT pin. The CONVERT
pin must stay low for at least two CCLK periods before going high for at least two CCLK
periods. Figure 12 shows the timing of a conversion start. The double falling arrow on
CCLK indicates the actual start of the conversion cycle.
Figure 12. Timing Diagram for Conversion Start Using CONVERT Pin
Appendix B explains the implementation examples of these features on the Prototyping
Board.
Figure 11. Current Flow from Ungrounded
or Floating Source
R0
2.2 nF
R1
2.2 nF
ADC
AIN0
AIN1
+
I
LN0
LN1
+
-
Device
CCLK
BUSY
CONV
Conversion starts
相關PDF資料
PDF描述
M3DGK-6036J IDC CABLE - MKR60K/MC60G/MCS60K
MAX6428OSUR+T IC MONITOR BAT LP SOT23-3
M3DEK-6036J IDC CABLE - MKR60K/MC60G/MCE60K
AFK106M50D16T-F CAP ALUM 10UF 50V 20% SMD
VI-26R-EY-S CONVERTER MOD DC/DC 7.5V 50W
相關代理商/技術參數
參數描述
101-1156 功能描述:開發板和工具包 - 其他處理器 RCM4200 Dev Kit (Intl) RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓:
101-115-6110-EV 功能描述:編碼器 1mA PUSH 220gf 12 PULSE 24 DETENTS RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C
101-115-6191-EV 功能描述:編碼器 1mA PUSH 220gf 12 PULSE 24 DETENTS RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C
101-1157 功能描述:開發板和工具包 - 其他處理器 RCM4100 Analog Dev Kit (US) RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓:
101-1158 功能描述:開發板和工具包 - 其他處理器 RCM4100 Analog Dev Kit (Intl) RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*