- 您現在的位置：買賣IC網 > PDF目錄67307 > 100230804 REDUZIERVERBINDUNG ZAPF 8MM ROHR 4MM PDF資料下載
參數資料
| 型號： | 100230804 |
| 英文描述： | REDUZIERVERBINDUNG ZAPF 8MM ROHR 4MM |
| 中文描述： | REDUZIERVERBINDUNG察普夫8毫米羅爾毫米 |
| 文件頁數： | 17/17頁 |
| 文件大?。?/td> | 269K |
| 代理商： | 100230804 |
Philips Semiconductors Programmable Logic Devices
Product specification
10H20EV8/10020EV8
ECL programmable array logic
October 22, 1993
121
AC TEST CIRCUIT
PULSE
GENERATOR
SCOPE
RT
L1
L3
VCC
VCO1
VCO2
VEE
SCOPE
L2
RT
CL
I1
I11
CLK/I12
FM
FN
FX
FY
DUT
+2.0V + 0.010V
–2.5V + 0.010V FOR 10020EV8
–3.2V + 0.010V FOR 10H20EV8
25
F
0.01
F
NOTES:
1. Use decoupling capacitors of 0.1
F and 25F from GND to VCC, and 0.01F and 25F from GND to VEE (0.01 and 0.1F capacitors
should be NPO Ceramic or MLC type). Decoupling capacitors should be placed as close as physically possible to the DUT and lead
length should be kept to less than 1/4 inch (6mm).
2. All unused inputs should be connected to either HIGH or LOW state consistent with the LOGIC function required.
3. All unused outputs are loaded with 50
to GND.
4. L1 and L2 are equal length 50 impedance lines. L3, the distance from the DUT pin to the junction of the cable from the Pulse
Generator and the cable to the Scope, should not exceed 1/4 inch (6mm).
5. RT = 50 terminator internal to Scope.
6. The unmatched wire stub between coaxial cable and pins under test must be less than 1/4 inch (6mm) long for proper test.
7. CL = Fixture and stray capacitance ≤ 3pF.
8. Any unterminated stubs connected anywhere along the transmission line between the Pulse Generator and the DUT or between the
DUT and the Scope should not exceed 1/4 inch (6mm) in length (refer to section on AC setup procedure).
9. All 50
resistors should have tolerance of ± 1% or better.
10. Test procedures are shown for only one input or set of input conditions. Other inputs are tested in the same manner.
25
F
0.1
F
相關PDF資料 |
PDF描述 |
|---|---|
| 100230806 | REDUZIERVERBINDUNG ZAPF 8MM ROHR 6MM |
| 100231006 | REDUZIERVERBINDUNG ZAPF 1MM ROHR 6MM |
| 100231008 | Pneufit Push-in Tube Fittings Metric |
| 100231206 | REDUZIERVERBINDUNG ZAPF 1MM ROHR 6MM |
| 100231208 | REDUZIERVERBINDUNG ZAPF 1MM ROHR 8MM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 100230806 | 制造商:NORGREN 功能描述:UNEQUAL STEM 8X6MM 制造商:NORGREN 功能描述:UNEQUAL STEM, 8X6MM 制造商:NORGREN 功能描述:UNEQUAL STEM, 8X6MM; Fitting Type:Reducer; Bore Size:6mm; External Diameter:8mm; SVHC:No SVHC (18-Jun-2012); Bore Diameter Max:6mm; External Diameter:12mm; Inlet Outside Diameter:8mm; Inlet Tube Diameter:6mm; Material:Brass; ;RoHS Compliant: NA |
| 1002310000 | 功能描述:CONN TERM BLOCK 5.08MM 5POS RoHS:是 類別:連接器，互連式 >> 接線座 - 接頭，插頭和插口 系列:Omnimate BLF 標準包裝:72 系列:Omnimate S2C 端接塊類型:接頭，公引腳，帶罩（4 面） 每電平位置:7 間距:0.138"（3.50mm） 級別數目:2 接頭定向:90°，直角 插頭導線入口:- 端子:焊接 線規:- 電流:10A 電壓:150V 安裝類型:通孔 特點:- 顏色:黑 包裝:散裝 配套產品:281-2980-ND - CONN TERM BLOCK PLUG 7POS 3.5MM 其它名稱:281-3034 |
| 100231006 | 制造商:NORGREN 功能描述:UNEQUAL STEM 10X6MM 制造商:NORGREN 功能描述:UNEQUAL STEM, 10X6MM |
| 100231008 | 制造商:NORGREN 功能描述:UNEQUAL STEM 10X8MM 制造商:NORGREN 功能描述:UNEQUAL STEM, 10X8MM |
| 100231206 | 制造商:NORGREN 功能描述:UNEQUAL STEM 12X6MM 制造商:NORGREN 功能描述:UNEQUAL STEM, 12X6MM 制造商:NORGREN 功能描述:UNEQUAL STEM, 12X6MM; Fitting Type:Reducer; Bore Size:6mm; External Diameter:12mm; SVHC:No SVHC (18-Jun-2012); Bore Diameter Max:6mm; External Diameter:14mm; Inlet Outside Diameter:12mm; Inlet Tube Diameter:6mm; Material:Brass; ;RoHS Compliant: NA |
發布緊急采購，3分鐘左右您將得到回復。