- 您現在的位置：買賣IC網 > PDF目錄23096 > 0ICAA-001-XTD DATACOM, INTERFACE CIRCUIT, PDSO8 PDF資料下載
參數資料
| 型號： | 0ICAA-001-XTD |
| 元件分類： | 網絡接口 |
| 英文描述： | DATACOM, INTERFACE CIRCUIT, PDSO8 |
| 封裝： | 0.150 INCH, GREEN, PLASTIC, SOIC-8 |
| 文件頁數： | 7/12頁 |
| 文件大小： | 560K |
| 代理商： | 0ICAA-001-XTD |
AMIS-42675 High-Speed Low Power CAN Transceiver
Data Sheet
For Long Networks
7.0 Functional Description
7.1 Operating Modes
AMIS-42675 provides two modes of operation as illustrated in Table 4. These modes are selectable through pin STB.
Table 4: Operating Modes
Pin RXD
Mode
Pin STB
Low
High
Normal
Low
Bus dominant
Bus recessive
Standby
High
Wake-up request detected
No wake-up request detected
7.1.1. Normal Mode
In the normal mode, the transceiver is able to communicate via the bus lines. The signals are transmitted and received to the CAN
controller via the pins TxD and RxD. The slopes on the bus lines outputs are optimized to give extremely low EME.
7.1.2. Stand-by Mode
In stand-by mode both the transmitter and receiver are disabled and a very low-power differential receiver monitors the bus lines for
CAN bus activity. The bus lines are terminated to ground and supply current is reduced to a minimum, typically 10A. When a wake-up
request is detected by the low-power differential receiver, the signal is first filtered and then verified as a valid wake signal after a time
period of tBUS, the RxD pin is driven low by the transceiver to inform the controller of the wake-up request.
7.2 Split Circuit
The VSPLIT pin is operational only in normal mode. In standby mode this pin is floating. The VSPLIT is connected as shown in Figure 2 and
its purpose is to provide a stabilized DC voltage of 0.5 x VCC to the bus avoiding possible steps in the common-mode signal therefore
reducing EME. These unwanted steps could be caused by an un-powered node on the network with excessive leakage current from the
bus that shifts the recessive voltage from its nominal 0.5 x VCC voltage.
7.3 Wake-up
Once a valid wake-up (dominant state longer than tBUS) has been received during the standby mode the RxD pin is driven low.
7.4 Over-temperature Detection
A thermal protection circuit protects the IC from damage by switching off the transmitter if the junction temperature exceeds a value of
approximately 160°C. Because the transmitter dissipates most of the power, the power dissipation and temperature of the IC is
reduced. All other IC functions continue to operate. The transmitter off-state resets when pin TxD goes high. The thermal protection
circuit is particularly needed when a bus line short circuits.
7.5 High Communication Speed Range
The transceiver is primarily intended for industrial applications. It allows very low baud rates needed for long bus length applications.
But also high speed communication is possible up to 1Mbit/s.
7.6 Fail Safe Features
A current-limiting circuit protects the transmitter output stage from damage caused by accidental short circuit to either positive or
negative supply voltage, although power dissipation increases during this fault condition.
The pins CANH and CANL are protected from automotive electrical transients (according to ISO 7637; see Figure 4). Pins TxD and
STB are pulled high internally should the input become disconnected. Pins TxD, STB and RxD will be floating, preventing reverse
supply should the VCC supply be removed.
4
AMI Semiconductor
–October 07, Rev. 1.0
www.amis.com
Specifications subject to change without notice
相關PDF資料 |
PDF描述 |
|---|---|
| 0ICAA-001-XTP | DATACOM, INTERFACE CIRCUIT, PDSO8 |
| 0ICAA-001-XTD | DATACOM, INTERFACE CIRCUIT, PDSO8 |
| 0ICAA-001-XTP | DATACOM, INTERFACE CIRCUIT, PDSO8 |
| 050-000-1854100 | RF Coaxial Connectors |
| 0ICAB-001-XTD | DATACOM, INTERFACE CIRCUIT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 0ICAA-001-XTP | 制造商:AMI 制造商全稱:AMI 功能描述:High-Speed Low Power CAN Transceiver |
| 0ICAB-001-XTD | 制造商:AMI 制造商全稱:AMI 功能描述:High-Speed CAN Transceiver |
| 0ICAB-001-XTP | 制造商:AMI 制造商全稱:AMI 功能描述:High-Speed CAN Transceiver |
| 0ICAG-001-XTD | 制造商:AMI 制造商全稱:AMI 功能描述:High Speed CAN Transceiver |
| 0ICAG-001-XTP | 制造商:AMI 制造商全稱:AMI 功能描述:High Speed CAN Transceiver |
發布緊急采購，3分鐘左右您將得到回復。