參數資料
型號: μPD780983
廠商: NEC Corp.
英文描述: 8 Bit Single Chip Microcontrollers(8 位單片微控制器)
中文描述: 8位單片機微控制器(8位單片微控制器)
文件頁數: 42/121頁
文件大?。?/td> 350K
代理商: ΜPD780983
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁
CHAPTER 3 CONTROL
42
(4)
Setting mode transition
Key input setting mode transition is performed. Table 3-13 lists the setting mode state transitions for key input.
During mode processing indicated by one of
<1>
to
<3>
in "Mode", upon the key input indicated in "Key,"
transition to the mode corresponding to the number shown is performed.
A "*" in a column indicates that the key is valid and that state transition is not performed.
A "-" in a column indicates that the key is invalid.
Table 3-13. Setting Mode State Transition
Mode
Key
[ON/OFF]
[+]
[-]
[Changeover]
<1>
Table setting
<3>
*
*
-
<2>
Output setting
<3>
*
*
<3>
<3>
OFF
*
<2>
<2>
*
Remark
Upon a reset start, table setting mode
<1>
is assumed.
(5)
Main mode transition
As indicated in Table 3-1 "State Transition," inverter output mode MMODE is changed and _MINIT is set.
_MINIT is the flag used for mode initialize processing, that is set only when the state is changed (upon a reset
start, depending on the initialize processing, stop mode is assumed). Table 3-14 lists the values set for
MMODE.
Table 3-14. MMODE Set Values
Main mode
MMODE
(Protection) stop mode
0
Fixed output mode
1
Output change mode
2
(6)
Inverter output variable setting (subroutine: INVSET)
In output change mode (MMODE = 2), every time the wait counter (decremented by 1 every 5 ms) reaches 0,
output frequency NFOUT is incremented or decremented by 1 such that it corresponds as closely as possible
to set target frequency RFOUT.
When the output frequency is changed, and when the settings of the carrier frequency, dead time, and rate of
frequency change are changed by key input (_PCHNG: set), the value of the transfer buffer for interrupt
variable setting is calculated as indicated in Table 3-15 (the method of calculation is given in
Table 3-3
).
To reference the interrupt variable by means of interrupt processing, a value is set in the transfer buffer during
main processing, and _CHNGST is set.
During interrupt processing _CHNGST is checked and, if set, the interrupt variable is set to the value in the
transfer buffer and _CHNGST is reset (
Figure 3-6
).
相關PDF資料
PDF描述
μPD780984 8 Bit Single Chip Microcontrollers
μPD780986 8 Bit Single Chip Microcontrollers
μPD780988 8 Bit Single Chip Microcontrollers
μPD78196Y 8 Bit Single Chip Microcontrollers(8 位單片微控制器)
μPD78197Y 8 Bit Single Chip Microcontrollers(8 位單片微控制器)
相關代理商/技術參數
參數描述
PD784054GCA2 制造商:NEC 制造商全稱:NEC 功能描述:16-BIT SINGLE-CHIP MICROCONTROLLER
PD784976A 制造商:NEC 制造商全稱:NEC 功能描述:16-Bit Single-Chip Microcontroller
PD7869 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic
PD78F0134 制造商:NEC 制造商全稱:NEC 功能描述:8-Bit Single-Chip Microcontrollers
PD78F0134(A) 制造商:NEC 制造商全稱:NEC 功能描述:8-Bit Single-Chip Microcontrollers