參數(shù)資料
型號: μPD754202
廠商: NEC Corp.
英文描述: 4 Bit Single Chip Microcontrollers(4位單片微控制器)
中文描述: 4位單片微控制器(4位單片微控制器)
文件頁數(shù): 64/66頁
文件大?。?/td> 339K
代理商: ΜPD754202
64
m
PD754202, 754202(A)
NOTES FOR CMOS DEVICES
1
PRECAUTION AGAINST ESD FOR SEMICONDUCTORS
Note: Strong electric field, when exposed to a MOS device, can cause destruction
of the gate oxide and ultimately degrade the device operation. Steps must be
taken to stop generation of static electricity as much as possible, and quickly
dissipate it once, when it has occurred. Environmental control must be
adequate. When it is dry, humidifier should be used. It is recommended to
avoid using insulators that easily build static electricity. Semiconductor
devices must be stored and transported in an anti-static container, static
shielding bag or conductive material. All test and measurement tools includ-
ing work bench and floor should be grounded. The operator should be
grounded using wrist strap. Semiconductor devices must not be touched with
bare hands. Similar precautions need to be taken for PW boards with
semiconductor devices on it.
2
HANDLING OF UNUSED INPUT PINS FOR CMOS
Note: No connection for CMOS device inputs can be cause of malfunction. If no
connection is provided to the input pins, it is possible that an internal input
level may be generated due to noise, etc., hence causing malfunction. CMOS
device behave differently than Bipolar or NMOS devices. Input levels of CMOS
devices must be fixed high or low by using a pull-up or pull-down circuitry.
Each unused pin should be connected to V
DD
or GND with a resistor, if it is
considered to have a possibility of being an output pin. All handling related
to the unused pins must be judged device by device and related specifications
governing the devices.
3
STATUS BEFORE INITIALIZATION OF MOS DEVICES
Note: Power-on does not necessarily define initial status of MOS device. Production
process of MOS does not define the initial operation status of the device.
Immediately after the power source is turned ON, the devices with reset
function have not yet been initialized. Hence, power-on does not guarantee
out-pin levels, I/O settings or contents of registers. Device is not initialized
until the reset signal is received. Reset operation must be executed immedi-
ately after power-on for devices having reset function.
相關PDF資料
PDF描述
μPD754202(A) 4 Bit Single Chip Microcontrollers(4位單片微控制器)
μPD754264 4 Bit RISC Microcontrollers(4 位單片微控制器)
μPD75F4246(A) 8 Bit Single Chip Microcontrollers
μPD75F4246 8 Bit Single Chip Microcontrollers
μPD75F4246A 8 Bit Single Chip Microcontrollers
相關代理商/技術參數(shù)
參數(shù)描述
PD75-473K 功能描述:固定電感器 47uH 10% .21ohm Choke SMT Power Ind RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm
PD75-563K 功能描述:固定電感器 56uH 10% .24ohm Choke SMT Power Ind RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm
PD75-683K 功能描述:固定電感器 68uH 10% .3ohm Choke SMT Power Ind RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm
PD75-823K 功能描述:固定電感器 82uH 10% .37ohm Choke SMT Power Ind RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm
PD75G6FK13 制造商:American Power Conversion Corp (APC by Schneider Electric) 功能描述:75KVA PDU W/ 480 PRI 208/120 SEC K13 RATED XMER 制造商:Schneider Electric 功能描述:APC 75KVA PDU W/ 480 PRI 20 - Bulk