- 您現在的位置：買賣IC網 > PDF目錄375033 > XCV812E-7BG404I (Xilinx, Inc.) Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays PDF資料下載
參數資料
| 型號： | XCV812E-7BG404I |
| 廠商： | Xilinx, Inc. |
| 英文描述： | Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| 中文描述： | 的Virtex娥內存擴展1.8伏現場可編程門陣列 |
| 文件頁數： | 19/116頁 |
| 文件大?。?/td> | 1087K |
| 代理商： | XCV812E-7BG404I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays
DS025-2 (v2.1) July 17, 2002
www.xilinx.com
1-800-255-7778
Module 2 of 4
15
R
At power-up, V
CC
must rise from 1.0 V to V
CC
min in less
than 50 ms, otherwise delay configuration by pulling
PROGRAM Low until V
CC
is valid.
SelectMAP Mode
The SelectMAP mode is the fastest configuration option.
Byte-wide data is written into the FPGA with a BUSY flag
controlling the flow of data.
An external data source provides a byte stream, CCLK, a
Chip Select (CS) signal and a Write signal (WRITE). If
BUSY is asserted (High) by the FPGA, the data must be
held until BUSY goes Low.
Data can also be read using the SelectMAP mode. If
WRITE is not asserted, configuration data is read out of the
FPGA as part of a readback operation.
After configuration, the pins of the SelectMAP port can be
used as additional user I/O. Alternatively, the port can be
retained to permit high-speed 8-bit readback.
Retention of the SelectMAP port is selectable on a
design-by-design basis when the bitstream is generated. If
retention is selected, PROHIBIT constraints are required to
prevent SelectMAP-port pins from being used as user I/O.
Multiple Virtex-E FPGAs can be configured using the
SelectMAP mode, and be made to start-up simultaneously.
To configure multiple devices in this way, wire the individual
CCLK, Data, WRITE, and BUSY pins of all the devices in
parallel. The individual devices are loaded separately by
asserting the CS pin of each device in turn and writing the
appropriate data. See
Table 11
for SelectMAP Write Timing
Characteristics.
Write
Write operations send packets of configuration data into the
FPGA. The sequence of operations for a multi-cycle write
operation is shown below. Note that a configuration packet
can be split into many such sequences. The packet does
not have to complete within one assertion of CS, illustrated
in
Figure 17
.
1.
Assert WRITE and CS Low. Note that when CS is
asserted on successive CCLKs, WRITE must remain
either asserted or de-asserted. Otherwise an abort is
initiated, as described below.
2.
Drive data onto D[7:0]. Note that to avoid contention,
the data source should not be enabled while CS is Low
and WRITE is High. Similarly, while WRITE is High, no
more that one CS should be asserted.
3.
At the rising edge of CCLK: If BUSY is Low, the data is
accepted on this clock. If BUSY is High (from a previous
write), the data is not accepted. Acceptance instead
occurs on the first clock after BUSY goes Low, and the
data must be held until this has happened.
4.
Repeat steps 2 and 3 until all the data has been sent.
5.
De-assert CS and WRITE.
Table 11:
SelectMAP Write Timing Characteristics
Description
Symbol
Values
Units
CCLK
D
0-7
Setup/Hold
1/2
T
SMDCC
/T
SMCCD
5.0 / 1.0
ns, min
CS Setup/Hold
3/4
T
SMCSCC
/T
SMCCCS
7.0 / 1.0
ns, min
WRITE Setup/Hold
5/6
T
SMCCW
/T
SMWCC
7.0 / 1.0
ns, min
BUSY Propagation Delay
7
T
SMCKBY
12.0
ns, max
Maximum Frequency
F
CC
66
MHz, max
Maximum Frequency with no handshake
F
CCNH
50
MHz, max
相關PDF資料 |
PDF描述 |
|---|---|
| XCV812E-7BG556C | Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| XCV812E-7BG556I | Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| XCV812E-7BG560C | Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| XCV812E-7BG560I | Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| XCV812E-7BG676C | Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XCV812E-7BG556C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| XCV812E-7BG556I | 制造商:XILINX 制造商全稱:XILINX 功能描述:Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| XCV812E-7BG560C | 功能描述:IC FPGA 1.8V C-TEMP 560-MBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:Virtex®-E EM 產品變化通告:XC4000(E,L) Discontinuation 01/April/2002 標準包裝:24 系列:XC4000E/X LAB/CLB數:100 邏輯元件/單元數:238 RAM 位總計:3200 輸入/輸出數:80 門數:3000 電源電壓:4.5 V ~ 5.5 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 100°C 封裝/外殼:120-BCBGA 供應商設備封裝:120-CPGA（34.55x34.55） |
| XCV812E-7BG560I | 制造商:XILINX 制造商全稱:XILINX 功能描述:Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| XCV812E-7BG676C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
發布緊急采購，3分鐘左右您將得到回復。