- 您現在的位置：買賣IC網 > PDF目錄375033 > XCV812E-6BG676I (Xilinx, Inc.) Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays PDF資料下載
參數資料
| 型號： | XCV812E-6BG676I |
| 廠商： | Xilinx, Inc. |
| 英文描述： | Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| 中文描述： | 的Virtex娥內存擴展1.8伏現場可編程門陣列 |
| 文件頁數： | 18/116頁 |
| 文件大?。?/td> | 1087K |
| 代理商： | XCV812E-6BG676I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays
Module 2 of 4
14
www.xilinx.com
1-800-255-7778
DS025-2 (v2.1) July 17, 2002
R
Master-Serial Mode
In master-serial mode, the CCLK output of the FPGA drives
a Xilinx Serial PROM that feeds bit-serial data to the DIN
input. The FPGA accepts this data on each rising CCLK
edge. After the FPGA has been loaded, the data for the next
device in a daisy-chain is presented on the DOUT pin after
the rising CCLK edge.
The interface is identical to slave-serial except that an inter-
nal oscillator is used to generate the configuration clock
(CCLK). A wide range of frequencies can be selected for
CCLK which always starts at a slow default frequency. Con-
figuration bits then switch CCLK to a higher frequency for
the remainder of the configuration. Switching to a lower fre-
quency is prohibited.
The CCLK frequency is set using the ConfigRate option in
the bitstream generation software. The maximum CCLK fre-
quency that can be selected is 60 MHz. When selecting a
CCLK frequency, ensure that the serial PROM and any
daisy-chained FPGAs are fast enough to support the clock
rate.
On power-up, the CCLK frequency is approximately
2.5 MHz. This frequency is used until the ConfigRate bits
have been loaded when the frequency changes to the
selected ConfigRate. Unless a different frequency is speci-
fied in the design, the default ConfigRate is 4 MHz.
Figure 13
shows a full master/slave system. In this system,
the left-most device operates in master-serial mode. The
remaining devices operate in slave-serial mode. The SPROM
RESET pin is driven by INIT, and the CE input is driven by
DONE. There is the potential for contention on the DONE pin,
depending on the start-up sequence options chosen.
The sequence of operations necessary to configure a
Virtex-E FPGA serially appears in
Figure 15
.
Figure 16
shows the timing of master-serial configuration.
Master-serial mode is selected by a <000> or <100> on the
mode pins (M2, M1, M0).
Table 10
shows the timing infor-
mation for
Figure 16
.
Figure 14:
Slave-Serial Mode Programming Switching Characteristics
4 T
CCH
3 T
CCO
5 T
CCL
2 T
CCD
1 T
DCC
DIN
CCLK
DOUT
(Output)
X5379_a
Figure 15:
Serial Configuration Flowchart
Apply Power
Set PROGRAM = High
Release INIT
If used to delay
Load a Configuration Bit
High
Low
FPGA makes a final
clearing pass and releases
INIT when finished.
FPGA starts to clear
configuration memory.
ds009_15_111799
Configuration Completed
BiEnd of
Yes
No
Once per bitstream,
FPGA checks data using CRC
and pulls INIT Low on error.
If no CRC errors found,
FPGA enters start-up phase
causing DONE to go High.
INIT
Figure 16:
Master-Serial Mode Programming Switching Characteristics
Serial Data In
CCLK
(Output)
Serial DOUT
(Output)
1 TDSCK
2
TCKDS
DS022_44_071201
相關PDF資料 |
PDF描述 |
|---|---|
| XCV812E-6BG900C | Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| XCV812E-6BG900I | Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| XCV812E-6FG404C | Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| XCV812E-6FG404I | Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| XCV812E-6FG556C | Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XCV812E-6BG900C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| XCV812E-6BG900I | 制造商:XILINX 制造商全稱:XILINX 功能描述:Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| XCV812E-6FG404C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| XCV812E-6FG404I | 制造商:XILINX 制造商全稱:XILINX 功能描述:Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| XCV812E-6FG556C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
發布緊急采購，3分鐘左右您將得到回復。