- 您現在的位置：買賣IC網 > PDF目錄375005 > XCA56011BU95 (MOTOROLA INC) 24-BIT DVD DIGITAL SIGNAL PROCESSOR PDF資料下載
參數資料
| 型號： | XCA56011BU95 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 數字信號處理 |
| 英文描述： | 24-BIT DVD DIGITAL SIGNAL PROCESSOR |
| 中文描述： | 8-BIT, 95 MHz, OTHER DSP, PQFP100 |
| 封裝： | PLASTIC, TQFP-100 |
| 文件頁數： | 75/82頁 |
| 文件大?。?/td> | 318K |
| 代理商： | XCA56011BU95 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁當前第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁
Preliminary Information
MOTOROLA
DSP56011 Technical Data Sheet, Rev. 1
4-3
Design Considerations
Electrical Design Considerations
PRELIMINARY
ELECTRICAL DESIGN CONSIDERATIONS
Use the following list of recommendations to assure correct DSP operation:
Provide a low-impedance path from the board power supply to each V
CC
pin
on the DSP, and from the board ground to each GND pin.
Use at least four 0.01–0.1
μ
F bypass capacitors positioned as close as possible
to the four sides of the package to connect the V
CC
power source to GND.
Ensure that capacitor leads and associated printed circuit traces that connect
to the chip V
CC
and GND pins are less than 0.5 in per capacitor lead.
Use at least a four-layer Printed Circuit Board (PCB) with two inner layers for
V
CC
and GND.
Because the DSP output signals have fast rise and fall times, PCB trace lengths
should be minimal. This recommendation particularly applies to the address
and data buses as well as the IRQA, IRQB, and NMI pins. Maximum Printed
Circuit Board (PCB) trace lengths on the order of 6 inches are recommended.
Consider all device loads as well as parasitic capacitance due to PCB traces
when calculating capacitance. This is especially critical in systems with higher
capacitive loads that could create higher transient currents in the V
CC
and
GND circuits.
All inputs must be terminated (i.e., not allowed to float) using CMOS levels,
Take special care to minimize noise levels on the V
CCP
and GND
P
pins.
If multiple DSP56011 devices are on the same board, check for cross-talk or
excessive spikes on the supplies due to synchronous operation of the devices.
CAUTION
This device contains protective circuitry to
guard against damage due to high static
voltage or electrical fields. However, normal
precautions are advised to avoid application
of any voltages higher than maximum rated
voltages to this high-impedance circuit.
Reliability of operation is enhanced if unused
inputs are tied to an appropriate logic voltage
level (e.g., either GND or V
CC
).
相關PDF資料 |
PDF描述 |
|---|---|
| XCB56011BU95 | 24-BIT DVD DIGITAL SIGNAL PROCESSOR |
| XCB56364FU100 | 24-Bit Audio Digital Signal Processor |
| XCB56364PV100 | 24-Bit Audio Digital Signal Processor |
| XCCACE-TQ144 | System ACE CompactFlash Solution |
| XCCACE-TQ144I | System ACE CompactFlash Solution |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XCAL4004DN | 功能描述:板上安裝壓力/力傳感器 3Vto16V 0 to 4 inH2O Transducer RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides |
| XCAL4004GN | 制造商:Honeywell Sensing and Control 功能描述:Pressure Sensor 0inH2O to 4inH2O Differential/Gage/Vacuum Gage 4-Pin |
| XCAL4010DN | 功能描述:板上安裝壓力/力傳感器 ASG/SENSYM RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides |
| XCAL4010GN | 制造商:Honeywell Sensing and Control 功能描述:Pressure Sensor 0inH2O to 10inH2O Differential/Gage/Vacuum Gage 4-Pin |
| XCAL5004DN | 制造商:Honeywell Sensing and Control 功能描述:Pressure Sensor 0inH2O to 4inH2O Bi-Directional Gage/Differential 4-Pin |
發布緊急采購，3分鐘左右您將得到回復。