參數資料
型號： XC4013E-5HG240I
廠商： Xilinx, Inc.
英文描述： Programmable Gate Arrays
中文描述： 可編程門陣列
文件頁數： 22/68頁
文件大小： 462K
代理商： XC4013E-5HG240I
R
XC4000E and XC4000X Series Field Programmable Gate Arrays
6-26
May 14, 1999 (Version 1.6)
or clear on reset and after configuration. Other than the glo-
bal GSR net, no user-controlled set/reset signal is available
to the I/O flip-flops. The choice of set or clear applies to
both the initial state of the flip-flop and the response to the
Global Set/Reset pulse. See
“Global Set/Reset” on
page 11
for a description of how to use GSR.
JTAG Support
Embedded logic attached to the IOBs contains test struc-
tures compatible with IEEE Standard 1149.1 for boundary
scan testing, permitting easy chip and board-level testing.
More information is provided in
“Boundary Scan” on
page 42
.
Three-State Buffers
A pair of 3-state buffers is associated with each CLB in the
array. (See
Figure 27 on page 30
.) These 3-state buffers
can be used to drive signals onto the nearest horizontal
longlines above and below the CLB. They can therefore be
used to implement multiplexed or bidirectional buses on the
horizontal longlines, saving logic resources. Programmable
pull-up resistors attached to these longlines help to imple-
ment a wide wired-AND function.
The buffer enable is an active-High 3-state (i.e. an
active-Low enable), as shown in
Table 13
.
Another 3-state buffer with similar access is located near
each I/O block along the right and left edges of the array.
(See
Figure 33 on page 34
.)
The horizontal longlines driven by the 3-state buffers have
a weak keeper at each end. This circuit prevents undefined
floating levels. However, it is overridden by any driver, even
a pull-up resistor.
Special longlines running along the perimeter of the array
can be used to wire-AND signals coming from nearby IOBs
or from internal longlines. These longlines form the wide
edge decoders discussed in
“Wide Edge Decoders” on
page 27
.
Three-State Buffer Modes
The 3-state buffers can be configured in three modes:
Standard 3-state buffer
Wired-AND with input on the I pin
Wired OR-AND
Standard 3-State Buffer
All three pins are used. Place the library element BUFT.
Connect the input to the I pin and the output to the O pin.
The T pin is an active-High 3-state (i.e. an active-Low
enable). Tie the T pin to Ground to implement a standard
buffer.
Wired-AND with Input on the I Pin
The buffer can be used as a Wired-AND. Use the WAND1
library symbol, which is essentially an open-drain buffer.
WAND4, WAND8, and WAND16 are also available. See the
XACT Libraries Guidefor further information.
The T pin is internally tied to the I pin. Connect the input to
the I pin and the output to the O pin. Connect the outputs of
all the WAND1s together and attach a PULLUP symbol.
Wired OR-AND
The buffer can be configured as a Wired OR-AND. A High
level on either input turns off the output. Use the
WOR2AND
library
symbol,
open-drain 2-input OR gate. The two input pins are func-
tionally equivalent. Attach the two inputs to the I0 and I1
pins and tie the output to the O pin. Tie the outputs of all the
WOR2ANDs together and attach a PULLUP symbol.
which
is
essentially
an
Three-State Buffer Examples
Figure 21
shows how to use the 3-state buffers to imple-
ment a wired-AND function. When all the buffer inputs are
High, the pull-up resistor(s) provide the High output.
Figure 22
shows how to use the 3-state buffers to imple-
ment a multiplexer. The selection is accomplished by the
buffer 3-state signal.
Pay particular attention to the polarity of the T pin when
using these buffers in a design. Active-High 3-state (T) is
identical to an active-Low output enable, as shown in
Table 13
.
Table 13: Three-State Buffer Functionality
IN
X
IN
T
1
0
OUT
Z
IN
P
U
L
L
U
P
Z = D
A
G
D
B
G
(D
C
+D
D
)
G
(D
E
+D
F
)
D
E
D
F
D
C
D
D
D
B
D
A
WAND1
WAND1
WOR2AND
WOR2AND
X6465
Figure 21: Open-Drain Buffers Implement a Wired-AND Function
相關PDF資料
PDF描述
XC4013E-5HG240M Programmable Gate Arrays
XC4013E-6HG240C Programmable Gate Arrays
XC4013E-6HG240I Programmable Gate Arrays
XC4013E-6HG240M Programmable Gate Arrays
XC4025 Logic Cell Array Family
相關代理商/技術參數
參數描述
XC4013E-5HG240M 制造商:XILINX 制造商全稱:XILINX 功能描述:Programmable Gate Arrays
XC4013E-5HQ240C 制造商:XILINX 制造商全稱:XILINX 功能描述:XC4000E and XC4000X Series Field Programmable Gate Arrays
XC4013E-5HQ240I 制造商:XILINX 制造商全稱:XILINX 功能描述:XC4000E and XC4000X Series Field Programmable Gate Arrays
XC4013E-5HQ240M 制造商:XILINX 制造商全稱:XILINX 功能描述:XC4000E and XC4000X Series Field Programmable Gate Arrays
XC4013E-5MQ240C 制造商:XILINX 制造商全稱:XILINX 功能描述:XC4000E and XC4000X Series Field Programmable Gate Arrays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*