- 您現在的位置：買賣IC網 > PDF目錄374964 > X9401YV24I-2.7 (INTERSIL CORP) Low Noise/Low Power/SPI Bus PDF資料下載
參數資料
| 型號： | X9401YV24I-2.7 |
| 廠商： | INTERSIL CORP |
| 元件分類： | 數字電位計 |
| 英文描述： | Low Noise/Low Power/SPI Bus |
| 中文描述： | QUAD 2.5K DIGITAL POTENTIOMETER, 3-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO24 |
| 封裝： | PLASTIC, TSSOP-24 |
| 文件頁數： | 4/20頁 |
| 文件大?。?/td> | 371K |
| 代理商： | X9401YV24I-2.7 |
4
FN8190.2
September 23, 2005
PIN NAMES
DEVICE DESCRIPTION
The X9401 is a highly integrated microcircuit incorpo-
rating four resistor arrays and their associated regis-
ters and counters and the serial interface logic
providing direct communication between the host and
the XDCP potentiometers.
Serial Interface
The X9401 supports the SPI interface hardware con-
ventions. The device is accessed via the SI input with
data clocked in on the rising SCK. CS must be LOW
and the HOLD and WP pins must be HIGH during the
entire operation.
The SO and SI pins can be connected together, since
they have three state outputs. This can help to reduce
system pin count.
Array Description
The X9401 is comprised of four resistor arrays. Each
array contains 63 discrete resistive segments that are
connected in series. The physical ends of each array
are equivalent to the fixed terminals of a mechanical
potentiometer (V
H
/R
H
and V
L
/R
L
inputs).
At both ends of each array and between each resistor
segment is a CMOS switch connected to the wiper
(V
W
/R
W
) output. Within each individual array only one
switch may be turned on at a time.
These switches are controlled by a Wiper Counter
Register (WCR). The six bits of the WCR are decoded
to select, and enable, one of sixty-four switches.
Wiper Counter Register (WCR)
The X9401 contains four Wiper Counter Registers,
one for each XDCP potentiometer. The WCR is equiv-
alent to a serial-in, parallel-out register/counter with its
outputs decoded to select one of sixty-four switches
along its resistor array. The contents of the WCR can
be altered in four ways: it may be written directly by
the host via the Write Wiper Counter Register instruc-
tion (serial load); it may be written indirectly by trans-
ferring the contents of one of four associated data
registers via the XFR Data Register or Global XFR
Data Register instructions (parallel load); it can be
modified one step at a time by the Increment/Decre-
ment instruction. Finally, it is loaded with the contents
of its data register zero (R0) upon power-up.
The Wiper Counter Register is a volatile register; that
is, its contents are lost when the X9401 is powered-
down. Although the register is automatically loaded
with the value in R
0
upon power-up, this may be differ-
ent from the value present at power-down. The wiper
position must be stored in R
0
to insure restoring the
wiper position after power-up.
Data Registers
Each potentiometer has four 6-bit nonvolatile data reg-
isters. These can be read or written directly by the
host. Data can also be transferred between any of the
four data registers and the associated Wiper Counter
Register. All operations changing data in one of the
data registers is a nonvolatile operation and will take a
maximum of 10ms.
If the application does not require storage of multiple
settings for the potentiometer, the data registers can
be used as memory locations for system parameters
or user preference data.
Data Register Detail
Symbol
Description
SCK
SI, SO
A
0
- A
1
V
H0
/R
H0
- V
H3
/R
H3
,
V
L0
/R
L0
- V
L3
/R
L3
V
W0
/R
W0
- V
W1
/R
W1
Serial Clock
Serial Data
Device Address
Potentiometers (terminal
equivalent)
Potentiometers (wiper
equivalent)
Hardware Write Protection
System Supply Voltage
System Ground
No Connection
WP
V
CC
V
SS
NC
(MSB)
D5
NV
(LSB)
D0
NV
D4
NV
D3
NV
D2
NV
D1
NV
X9401
相關PDF資料 |
PDF描述 |
|---|---|
| X95820UV14I-2.7 | ADAPTER SOP FOR BK842/843 |
| X95820WV14I-2.7 | Dual Digital Controlled Potentiometers |
| X95820WV14IZ-2.7 | Dual Digital Controlled Potentiometers |
| X95820 | Dual Digital Controlled Potentiometers |
| XAMR20A | 16 SEGMENT SINGLE DIGIT ALPHANUMERIC DISPLAY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9408 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad Digitally Controlled (XDCP?) Potentiometers |
| X9408_09 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad Digitally Controlled (XDCP?) Potentiometers |
| X9408-2.7 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Noise/Low Power/2-Wire Bus |
| X9408WP24 | 功能描述:IC XDCP QUAD 64-TAP 10K 24-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| X9408WP24-2.7 | 功能描述:IC XDCP QUAD 64-TAP 10K 24-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。