參數資料
型號: W65C02S6Q-14
廠商: Electronic Theatre Controls, Inc.
英文描述: Microprocessor
中文描述: 微處理器
文件頁數: 11/40頁
文件大小: 1011K
代理商: W65C02S6Q-14
The Western Design Center, Inc.
W65C02S Data Sheet
The Western Design Center, Inc. W65C02S Data Sheet
11
3.11
Reset (RESB)
The Reset (RESB) input is used to initialize the microprocessor and start program execution. The RESB signal must
be held low for at least two clock cycles after VDD reaches operating voltage. Ready (RDY) has no effect while
RESB is being held low. All Registers are initialized by software except the Decimal and Interrupt disable mode
select bits of the Processor Status Register (P) are initialized by hardware. When a positive edge is detected, there
will be a reset sequence lasting seven clock cycles. The program counter is loaded with the reset vector from
locations FFFC (low byte) and FFFD (high byte). This is the start location for program control. RESB should be
held high after reset for normal operation.
Processor Status Register (P)
7
6
5
4
*
*
1
1
N
V
B
*=software initialized
3.12
Set Overflow (SOB)
A negative transition on the
Set Overflow (SOB)
pin sets the overflow bit (V) in the status code register. The signal is
sampled on the rising edge of PHI2. SOB was originally intended for fast input recognition because it can be tested
with a branch instruction; however, it is not recommended in new system design and was seldom used in the past.
3.13
SYNChronize with OpCode fetch (SYNC)
The OpCode fetch cycle of the microprocessor instruction is indicated with SYNC high. The SYNC output is
provided to identify those cycles during which the microprocessor is fetching an OpCode. The SYNC line goes high
during the clock cycle of an OpCode fetch and stays high for the entire cycle. If the RDY line is pulled low during
the clock cycle in which SYNC went high, the processor will stop in its current state and will remain in the state
until the RDY line goes high. In this manner, the SYNC signal can be used to control RDY to cause single
instruction execution.
3.14
Power (VDD) and Ground (VSS)
VDD is the positive power supply voltage and VSS is system logic ground.
3.15
Vector Pull (VPB)
The Vector Pull (VPB) output indicates that a vector location is being addressed during an interrupt sequence. VPB
is low during the last interrupt sequence cycles, during which time the processor reads the interrupt vector. The
VPB signal may be used to select and prioritize interrupts from several sources by modifying the vector addresses.
3
0
D
2
1
I
1
*
Z
0
*
C
相關PDF資料
PDF描述
W65C02S8P-14 Microprocessor
W65C02S8PL-14 Microprocessor
W65C02S8Q-14 Microprocessor
W65C02SP-14 Microprocessor
W65C02SPL-14 Microprocessor
相關代理商/技術參數
參數描述
W65C02S6TPG-14 功能描述:微處理器 - MPU 8-bit Microprocessor RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
W65C02S6TPLG-14 功能描述:微處理器 - MPU 8-bit Microprocessor RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
W65C02S6TQG-14 功能描述:微處理器 - MPU 8-bit Microprocessor RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
W65C02S8P-14 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microprocessor
W65C02S8PL-14 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microprocessor