- 您現在的位置：買賣IC網 > PDF目錄385015 > TR7000 (RF Monolithics, Inc.) 433.92 MHz Hybrid Transceiver PDF資料下載
參數資料
| 型號： | TR7000 |
| 廠商： | RF Monolithics, Inc. |
| 英文描述： | 433.92 MHz Hybrid Transceiver |
| 中文描述： | 433.92兆赫混合收發器 |
| 文件頁數： | 9/14頁 |
| 文件大?。?/td> | 156K |
| 代理商： | TR7000 |
RF Monolithics, Inc.
RFM Europe
1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
Phone: (972) 233-2903
Phone: 44 1963 251383
Fax: (972) 387-8148
Fax: 44 1963 251510
E-mail: info@rfm.com Page 9 of 14
http://www.rfm.com
TR7000-111706
Pin Descriptions
Pin
Name
Description
1
GND1
GND1 is the RF ground pin.
2
VCC1
VCC1 is a positive supply voltage pin. VCC1 is decoupled with a ferrite bead and bypassed by an RF capacitor.
3
VCC3
VCC3 is a positive supply voltage pin. VCC3 is bypassed by an RF capacitor.
4
PKDET
This pin controls the peak detector operation. A capacitor between this pin and ground sets the peak detector attack and
decay times, which have a fixed 1:1000 ratio. For most applications, these time constants should be coordinated with the
base-band time constant. For a given base-band capacitor C
BBO
, the capacitor value C
PKD
is:
C
PKD
= 2.0* C
BBO
, where C
BBO
and C
PKD
are in pF
A ±10% ceramic capacitor should be used at this pin. This time constant will vary between t
PKA
and 1.5* t
PKA
with varia-
tions in supply voltage, temperature, etc. The capacitor is driven from a 200 ohm “attack” source, and decays through a
200 K load. The peak detector is used to drive the “dB-below-peak” data slicer and the AGC release function. The peak
detector capacitor is discharged in the receiver power-down (sleep) mode and in the transmit modes.
5
BBOUT
BBOUT is the receiver base-band output pin. This pin drives the CMPIN pin through a coupling capacitor C
BBO
for internal
data slicer operation. The time constant t
BBC
for this connection is:
t
BBC
= 0.1C
BBO
, where t
BBC
is in μs and C
BBO
is in pF
A ±10% ceramic capacitor should be used between BBOUT and CMPIN. The time constant can vary between t
BBC
and
1.8*t
BBC
with variations in supply voltage, temperature, etc. The optimum time constant in a given circumstance will
depend on the data rate, data run length, and other factors as discussed in the ASH Transceiver Designer’s Guide.
C
BBO
= 11.2*SP
MAX
, where SP
MAX
is the maximum signal pulse width in μs and C
BBO
is in pF
The output from this pin can also be used to drive an external data recovery process (DSP, etc.). The nominal output
impedance of this pin is 1 K. When the receiver RF amplifiers are operating at a 50%-50% duty cycle, the BBOUT signal
changes about 10 mV/dB, with a peak-to-peak signal level of up to 450 mV. The signal at BBOUT is riding on a 1.5 Vdc
value that varies somewhat with supply voltage and temperature, so it should be coupled through a capacitor to an exter-
nal load. A load impedance of 50 K to 500 K in parallel with no more than 10 pF is recommended. When an external data
recovery process is used with AGC, BBOUT must be coupled to the external data recovery process and CMPIN by sepa-
rate series coupling capacitors. The AGC reset function is driven by the signal applied to CMPIN. When the transceiver is
in power-down (sleep) or in a transmit mode, the output impedance of this pin becomes very high, preserving the charge
on the coupling capacitor.
6
CMPIN
This pin is the input to the internal data slicers. It is driven from BBOUT through a coupling capacitor. The input impedance
of this pin is 100 K.
7
RXDATA
RXDATA is the receiver data output pin. It is a CMOS output. The signal on this pin can come from one of two sources.
The default source is directly from the output of the data slicer circuit. The alternate source is from the radio’s internal data
and clock recovery circuit. When the internal data and clock recovery circuit is used, the signal on RXDATA is switched
from the output of the data slicer to the output of the data and clock recovery circuit when a packet start symbol is detected.
Each recovered data bit is then output on the rising edge of a RXDCLK pulse (Pin 14), and is stable for reading on the fall-
ing edge of the RXDCLK pulse.
8
TXMOD
The transmitter RF output voltage is proportional to the input current to this pin. A resistor in series with the TXMOD input
is normally used to adjust the peak transmitter output. Full transmitter power (10 mW) requires about 235 μA of drive cur-
rent. The transmitter output power P
O
for a 3 Vdc supply voltage is approximately:
PO = 180*(I
TXM
)
2
, where PO is in mW and the modulation current I
TXM
is in mA
The practical power control range is 10 to -50 dBm. A ±5% TXMOD resistor value is recommended. Internally, this pin is
connected to the base of a bipolar transistor with a small emitter resistor. The voltage at the TXMOD input pin is about 0.85
volt with 235 uA of drive current. This pin accepts analog modulation and can be driven with either logic level data pulses
(unshaped) or shaped data pulses.
9
LPFADJ
This pin is the receiver low-pass filter bandwidth adjust. The filter bandwidth is set by a resistor R
LPF
between this pin and
ground. The resistor value can range from 510 K to 3 K, providing a filter 3 dB bandwidth f
LPF
from 5 to 600 kHz. The resis-
tor value is determined by:
R
LPF
= (0.0006*f
LPF
)
-1.069
where R
LPF
is in kilohms, and f
LPF
is in kHz
A ±5% resistor should be used to set the filter bandwidth. This will provide a 3 dBfilter bandwidth between f
LPF
and
1.3* f
LPF
with variations in supply voltage, temperature, etc. The filter provides a three-pole, 0.05 degree equiripple phase
response.D input is normally used to
10
GND2
GND2 is an IC ground pin.
相關PDF資料 |
PDF描述 |
|---|---|
| TR8001 | 868.35 MHz Hybrid Transceiver |
| TR8100 | 916.50 MHz Hybrid Transceiver |
| TRA06E | Thin Film, Resistor Array |
| TRA06E0803101BRT1 | MS3102A36-6P W/P CAP |
| TRA06E0803101DRT1 | Thin Film, Resistor Array |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TR7001 | 功能描述:射頻收發器 3G ASH Transceiver 315 MHz 115.2 kbps RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| TR7002 | 功能描述:射頻接收器 3G ASH Transceiver 418 MHz 115.2 kbps RoHS:否 制造商:Skyworks Solutions, Inc. 類型:GPS Receiver 封裝 / 箱體:QFN-24 工作頻率:4.092 MHz 工作電源電壓:3.3 V 封裝:Reel |
| TR7003 | 功能描述:射頻收發器 3G ASH Transceiver 303.825MHz 115.2kbps RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| TR7025-10W | 制造商:Distributed By MCM 功能描述:10W Speaker Line Matching Transformer |
| TR7025-30W | 制造商:Distributed By MCM 功能描述:30W Speaker Line Matching Transformer |
發布緊急采購，3分鐘左右您將得到回復。