- 您現在的位置：買賣IC網 > PDF目錄385015 > TR7000 (RF Monolithics, Inc.) 433.92 MHz Hybrid Transceiver PDF資料下載
參數資料
| 型號： | TR7000 |
| 廠商： | RF Monolithics, Inc. |
| 英文描述： | 433.92 MHz Hybrid Transceiver |
| 中文描述： | 433.92兆赫混合收發器 |
| 文件頁數： | 7/14頁 |
| 文件大?。?/td> | 156K |
| 代理商： | TR7000 |
RF Monolithics, Inc.
RFM Europe
1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
Phone: (972) 233-2903
Phone: 44 1963 251383
Fax: (972) 387-8148
Fax: 44 1963 251510
E-mail: info@rfm.com Page 7 of 14
http://www.rfm.com
TR7000-111706
Figure 3
Adress
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
CFG0
Sleep
TX/RX
ASK/OOK
-
Mode 1
Mode 0
-
SV En
1
CFG1
-
-
-
-
BR3
BR2
BR1
BR0
2
LoSyn
Test
LOSyn6
LOSyn5
LOSyn4
LOSyn3
LOSyn2
LOSyn1
LOSyn0
CFG0 Bit 6 - When this bit is 0, the radio is in the receive mode (provided
CFG0 Bit 7 is 0). When this bit is 1, the radio is in one of the transmit
modes. Note the radio will transmit using OOK or ASK modulation,
depending on the value of CFG0 Bit 5. The power-on default value of this
bit is 0.
CFG0 Bit 5 - When this bit is 0, the transmitter uses OOK modulation.
When this bit is 1, the transmitter uses ASK modulation. The power-on
default value of this bit is 0.
CFG0 Bit 4 - This bit should always be set to 0 in the TR7000. The power-
on default value of this bit is 0.
CFG0 Bits 3, 2 - The states of these two bits set the basic operating mode
of the radio as shown below. The power-on default value of these two
bits is 0.
CFG0 Bit 1 - This bit should always be set to 0 in the TR7000. The power-
on default value of this bit is 0.
CFG0 Bit 0 - Setting this bit to logic 1 enables the internal start symbol
(vector) detection and the data and clock recovery circuit. When active,
this function continuously tests for a 16-bit start symbol, 0xE2E2 (hex).
Data clocking begins in the middle of the first bit following the 16-bit start
symbol, and clocking continues until CFG0 Bit 0 is reset to a logic 0.
Note
that CFG0 Bit 0 must be set to back to a
logic 1 to re-enable the start sym-
bol detection and the data and
clock recovery circui
t. The common way to
use this function is for the host processor to set this bit to a 1 when it is
ready to receive a message. When a start symbol is detected, data clock-
ing begins, and the host processor inputs the message bits. Once all of
the bits in the message are received, the host processor resets this bit to 0
to end data clocking. After the current message has been processed, the
host processor sets this bit to 1 again to enable detection of the next mes-
sage. The power-on default value of this bit is 0.
The start symbol pattern is sent starting with the MSB. This start symbol
pattern will not occur in a message that has been encoded for DC-balance
using either Manchester encoding or 8-to-12 bit symbolization using the
encoding table given below. Note that the table is given for 4-to-6 bit
encoding, so each byte of the message is encoded starting with the high
nibble and then the low nibble.
CFG1 Bit 7 - This bit is unused in the TR7000.
CFG1 Bit 6 - This bit is unused in the TR7000.
CFG1 Bit 5 - This bit is unused in the TR7000.
CFG1 Bit 4 - This bit is unused in the TR7000.
CFG1 Bits 3, 2, 1, 0 - These bits select the internal data and clock recov-
ery data (bit) rate as shown in the table below. The power-on default value
of these bits is 0.
LOSyn Bit 7 - This bit is only used in product testing. It should always be
set to 0 for normal operation. The power-on default value of this bit is 0.
LOSyn Bits 6, 5, 4, 3, 2, 1, 0 -These bits have no function in the TR7000
and can be written as either a logic 1 or a logic 0.
Note that data to/from the configuration registers is clocked in/out MSB
first. See the Control Register Read/Write Detail and Control Register
Read/Write Timing Drawings for additional details.
Bit 3
Bit 2
Mode
0
0
Single-channel Mode
0
1
Not Used
1
0
Not Used
1
1
Not Used
Nibble Hex Value
Symbol Hex Value (6 bits)
0
0D
1
0E
2
13
3
15
4
16
5
19
6
1A
7
1C
8
23
9
25
A
26
B
29
C
2A
D
2C
E
32
F
34
相關PDF資料 |
PDF描述 |
|---|---|
| TR8001 | 868.35 MHz Hybrid Transceiver |
| TR8100 | 916.50 MHz Hybrid Transceiver |
| TRA06E | Thin Film, Resistor Array |
| TRA06E0803101BRT1 | MS3102A36-6P W/P CAP |
| TRA06E0803101DRT1 | Thin Film, Resistor Array |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TR7001 | 功能描述:射頻收發器 3G ASH Transceiver 315 MHz 115.2 kbps RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| TR7002 | 功能描述:射頻接收器 3G ASH Transceiver 418 MHz 115.2 kbps RoHS:否 制造商:Skyworks Solutions, Inc. 類型:GPS Receiver 封裝 / 箱體:QFN-24 工作頻率:4.092 MHz 工作電源電壓:3.3 V 封裝:Reel |
| TR7003 | 功能描述:射頻收發器 3G ASH Transceiver 303.825MHz 115.2kbps RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| TR7025-10W | 制造商:Distributed By MCM 功能描述:10W Speaker Line Matching Transformer |
| TR7025-30W | 制造商:Distributed By MCM 功能描述:30W Speaker Line Matching Transformer |
發布緊急采購，3分鐘左右您將得到回復。