- 您現在的位置：買賣IC網 > PDF目錄385014 > TR1004 (RF Monolithics, Inc.) 914.00 MHz Hybrid Transceiver PDF資料下載
參數資料
| 型號： | TR1004 |
| 廠商： | RF Monolithics, Inc. |
| 英文描述： | 914.00 MHz Hybrid Transceiver |
| 中文描述： | 914.00兆赫混合收發器 |
| 文件頁數： | 4/12頁 |
| 文件大?。?/td> | 105K |
| 代理商： | TR1004 |
RF Monolithics, Inc.
RFM Europe
1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
Phone: (972) 233-2903
Phone: 44 1963 251383
Fax: (972) 387-8148
Fax: 44 1963 251510
E-mail: info@rfm.com Page 4 of 12
http://www.rfm.com
TR1004-070105
ASH Receiver Block Diagram & Timing Cycle
Antenna
Pulse
Generator
SAW
Delay Line
SAW Filter
RFA1
RFA2
Data
Out
Detector &
Low-Pass
Filter
RF Data Pulse
P1
P2
RFA1 Out
RF Input
P1
Delay Line
Out
P2
t
PW2
t
PW1
t
PRI
t
PRC
Figure 1
ASH Transceiver Theory of Operation
Introduction
RFM’s amplifier-sequenced hybrid (ASH) transceiver is specifically de-
signed for short-range wireless data communication applications. The
transceiver provides robust operation, very small size, low power con-
sumption and low implementation cost. All critical RF functions are con-
tained in the hybrid, simplifying and speeding design-in. The ASH
transceiver can be readily configured to support a wide range of data rates
and protocol requirements. The transceiver features excellent suppression
of transmitter harmonics and virtually no RF emissions when receiving,
making it easy to certify to short- range (unlicensed) radio regulations.
Amplifier-Sequenced Receiver Operation
The ASH transceiver’s unique feature set is made possible by its system
architecture. The heart of the transceiver is the amplifier- sequenced re-
ceiver section, which provides more than 100 dB of stable RF and detector
gain without any special shielding or decoupling provisions. Stability is
achieved by distributing the total RF gain over
time
. This is in contrast to a
superheterodyne receiver, which achieves stability by distributing total RF
gain over multiple frequencies.
Figure 1 shows the basic block diagram and timing cycle for an amplifier-
sequenced receiver. Note that the bias to RF amplifiers RFA1 and RFA2
are independently controlled by a pulse generator, and that the two ampli-
fiers are coupled by a surface acoustic wave (SAW) delay line, which has
a typical delay of 0.5 μs.
An incoming RF signal is first filtered by a narrow-band SAW filter, and is
then applied to RFA1. The pulse generator turns RFA1 ON for 0.5 μs. The
amplified signal from RFA1 emerges from the SAW delay line at the input
to RFA2. RFA1 is now switched OFF and RFA2 is switched ON for 0.55 μs,
amplifying the RF signal further. The ON time for RFA2 is usually set at 1.1
times the ON time for RFA1, as the filtering effect of the SAW delay line
stretches the signal pulse from RFA1 somewhat. As shown in the timing di-
agram, RFA1 and RFA2 are never on at the same time, assuring excellent
receiver stability. Note that the narrow-band SAW filter eliminates sampling
sideband responses outside of the receiver passband, and the SAW filter
and delay line act together to provide very high receiver ultimate rejection.
Amplifier-sequenced receiver operation has several interesting character-
istics that can be exploited in system design. The RF amplifiers in an am-
plifier-sequenced receiver can be turned on and off almost instantly,
allowing for very quick power-down (sleep) and wake-up times. Also, both
RF amplifiers can be off between ON sequences to trade-off receiver noise
figure for lower average current consumption. The effect on noise figure
can be modeled as if RFA1 is on continuously, with an attenuator placed in
front of it with a loss equivalent to 10*log
10
(RFA1 duty factor), where the
duty factor is the average amount of time RFA1 is ON (up to 50%). Since
an amplifier-sequenced receiver is inherently a sampling receiver, the
overall cycle time between the start of one RFA1 ON sequence and the
start of the next RFA1 ON sequence should be set to sample the narrowest
RF data pulse at least 10 times. Otherwise, significant edge jitter will be
added to the detected data pulse.
相關PDF資料 |
PDF描述 |
|---|---|
| TR1100 | 916.50 MHz Hybrid Transceiver |
| TR3001 | 315.00 MHz Hybrid Transceiver |
| TR3005 | 403.50 MHz Hybrid Transceiver |
| TR3100 | 433.92 MHz Hybrid Transceiver |
| TR40-16B | TR40-16B |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TR1004PF31NB | 制造商:ITT Interconnect Solutions 功能描述:CABLE SOCKET TRIDENT 10/4 |
| TR1004PFS1NB | 制造商:ITT Interconnect Solutions 功能描述:JACK FREE 4WAY 制造商:ITT Interconnect Solutions 功能描述:JACK, FREE, 4WAY 制造商:ITT Interconnect Solutions 功能描述:JACK, FREE, 4WAY; Connector Type:Circular Industrial; Gender:Plug; Contact Gender:Socket; Connector Mounting:Cable; Connector Shell Size:10; Insert Arrangement:10-04; No. of Positions:4; SVHC:No SVHC (19-Dec-2012); Series:TRIDENT ;RoHS Compliant: Yes |
| TR1004PFS1NB | 制造商:ITT Interconnect Solutions 功能描述:JACK FREE 4 WAY |
| TR1004PMS1NB | 制造商:ITT Interconnect Solutions 功能描述:PLUG FREE 4WAY 制造商:ITT Interconnect Solutions 功能描述:PLUG, FREE, 4WAY 制造商:ITT Interconnect Solutions 功能描述:CIRCULAR CONN, PLUG, SZ 10-04, 4POS, CABLE; Connector Type:Circular Industrial; Connector Body Material:Nylon (Polyamide); Gender:Plug; Contact Gender:Socket; Connector Mounting:Cable; Connector Shell Size:10; Insert Arrangement:10-4;RoHS Compliant: Yes 制造商:ITT 功能描述:TRIDENT RINGLOCK UP TO 13 A CONTACT CURRENT RATING 制造商:ITT 功能描述:Conn Ringlock Circular PIN 4 POS Crimp ST Cable Mount 4 Terminal 1 Port |
| TR1004PMS1NB | 制造商:ITT Interconnect Solutions 功能描述:PLUG FREE 4 WAY |
發布緊急采購，3分鐘左右您將得到回復。