- 您現在的位置：買賣IC網 > PDF目錄385014 > TR1004 (RF Monolithics, Inc.) 914.00 MHz Hybrid Transceiver PDF資料下載
參數資料
| 型號： | TR1004 |
| 廠商： | RF Monolithics, Inc. |
| 英文描述： | 914.00 MHz Hybrid Transceiver |
| 中文描述： | 914.00兆赫混合收發器 |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 105K |
| 代理商： | TR1004 |
RF Monolithics, Inc.
RFM Europe
1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
Phone: (972) 233-2903
Phone: 44 1963 251383
Fax: (972) 387-8148
Fax: 44 1963 251510
E-mail: info@rfm.com Page 11 of 12
http://www.rfm.com
TR1004-070105
Pin
Name
Description
15
PWIDTH
The PWIDTH pin sets the width of the ON pulse to the first RF amplifier t
PW1
with a resistor R
PW
to ground (the ON pulse
width to the second RF amplifier t
PW2
is set at 1.1 times the pulse width to the first RF amplifier). The ON pulse width t
PW1
can be adjusted between 0.55 and 1 μs with a resistor value in the range of 200 K to 390 K. The value of R
PW
is given by:
R
PW
= 404* t
PW1
- 18.6, where t
PW1
is in μs and R
PW
is in kilohms
A ±5% resistor value is recommended. When this pin is connected to Vcc through a 1 M resistor, the RF amplifiers operate
at a nominal 50%-50% duty cycle, facilitating high data rate operation. In this case, the RF amplifier ON times are con-
trolled by the PRATE resistor as described above. It is important to keep the total capacitance between ground, Vcc and
this node to less than 5 pF to maintain stability. When using the high data rate operation with the sleep mode, connect the
1 M resistor between this pin and CNTRL1 (Pin 17), so this pin is low in the sleep mode.
16
VCC2
VCC2 is the positive supply voltage pin for the receiver RF section and transmitter oscillator. Pin 16 must be bypassed with
an RF capacitor, and must also be bypassed with a 1 to 10 μF tantalum or electrolytic capacitor. See the ASH Transceiver
Designer’s Guide for additional information.
17
CNTRL1
CNTRL1 and CNTRL0 select the receive and transmit modes. CNTRL1 and CNTRL0 both high place the unit in the
receive mode. CNTRL1 high and CNTRL0 low place the unit in the ASK transmit mode. CNTRL1 low and CNTRL0 high
place the unit in the OOK transmit mode. CNTRL1 and CNTRL0 both low place the unit in the power-down (sleep) mode.
CNTRL1 is a high-impedance input (CMOS compatible). An input voltage of 0 to 300 mV is interpreted as a logic low. An
input voltage of Vcc - 300 mV or greater is interpreted as a logic high. An input voltage greater than Vcc + 200 mV should
not be applied to this pin. A logic high requires a maximum source current of 40 μA. A logic low requires a maximum sink
current of 25 μA (1 μA in sleep mode). This pin must be held at a logic level; it cannot be left unconnected.
18
CNTRL0
CNTRL0 is used with CNTRL1 to control the receive and transmit modes of the transceiver. CNTRL0 is a high-impedance
input (CMOS compatible). An input voltage of 0 to 300 mV is interpreted as a logic low. An input voltage of Vcc - 300 mV or
greater is interpreted as a logic high. An input voltage greater than Vcc + 200 mV should not be applied to this pin. A logic
high requires a maximum source current of 40 μA. A logic low requires a maximum sink current of 25 μA (1 μA in sleep
mode). This pin must be held at a logic level; it cannot be left unconnected.
19
GND3
GND3 is an IC ground pin. It should be connected to GND1 by a short, low inductance trace.
20
RFIO
RFIO is the RF input/output pin. This pin is connected directly to the SAW filter transducer. Antennas presenting an imped-
ance in the range of 35 to 72 ohms resistive can be satisfactorily matched to this pin with a series matching coil and a
shunt matching/ESD protection coil. Other antenna impedances can be matched using two or three components. For
some impedances, two inductors and a capacitor will be required. A DC path from RFIO to ground is required for ESD pro-
tection.
SM-20H PCB Pad Layout
Dimensions in inches.
.09
.370
0.000
0
.065
.105
.145
.185
.225
.265
.305
.345
.
.435
.
.
.
.
.
.
相關PDF資料 |
PDF描述 |
|---|---|
| TR1100 | 916.50 MHz Hybrid Transceiver |
| TR3001 | 315.00 MHz Hybrid Transceiver |
| TR3005 | 403.50 MHz Hybrid Transceiver |
| TR3100 | 433.92 MHz Hybrid Transceiver |
| TR40-16B | TR40-16B |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TR1004PF31NB | 制造商:ITT Interconnect Solutions 功能描述:CABLE SOCKET TRIDENT 10/4 |
| TR1004PFS1NB | 制造商:ITT Interconnect Solutions 功能描述:JACK FREE 4WAY 制造商:ITT Interconnect Solutions 功能描述:JACK, FREE, 4WAY 制造商:ITT Interconnect Solutions 功能描述:JACK, FREE, 4WAY; Connector Type:Circular Industrial; Gender:Plug; Contact Gender:Socket; Connector Mounting:Cable; Connector Shell Size:10; Insert Arrangement:10-04; No. of Positions:4; SVHC:No SVHC (19-Dec-2012); Series:TRIDENT ;RoHS Compliant: Yes |
| TR1004PFS1NB | 制造商:ITT Interconnect Solutions 功能描述:JACK FREE 4 WAY |
| TR1004PMS1NB | 制造商:ITT Interconnect Solutions 功能描述:PLUG FREE 4WAY 制造商:ITT Interconnect Solutions 功能描述:PLUG, FREE, 4WAY 制造商:ITT Interconnect Solutions 功能描述:CIRCULAR CONN, PLUG, SZ 10-04, 4POS, CABLE; Connector Type:Circular Industrial; Connector Body Material:Nylon (Polyamide); Gender:Plug; Contact Gender:Socket; Connector Mounting:Cable; Connector Shell Size:10; Insert Arrangement:10-4;RoHS Compliant: Yes 制造商:ITT 功能描述:TRIDENT RINGLOCK UP TO 13 A CONTACT CURRENT RATING 制造商:ITT 功能描述:Conn Ringlock Circular PIN 4 POS Crimp ST Cable Mount 4 Terminal 1 Port |
| TR1004PMS1NB | 制造商:ITT Interconnect Solutions 功能描述:PLUG FREE 4 WAY |
發布緊急采購，3分鐘左右您將得到回復。