參數資料
型號: TQFN34-20
廠商: ANADIGICS, Inc.
英文描述: Four-Channel Backlight Driver with Dual LDOs
中文描述: 四通道雙LDO的背光驅動器
文件頁數: 14/20頁
文件大?。?/td> 392K
代理商: TQFN34-20
AAT2847
Four-Channel Backlight Driver with Dual LDOs
14
2847.2007.09.1.0
Auto Disable Feature
The charge pump in the AAT2847 is equipped with
an auto-disable feature for each LED channel. After
the IC is enabled and successively starts-up, a test
current of 100μA (typical) is forced through each
LED channel. The channel will be disabled if the
voltage on that particular DX pin does not drop to
certain threshold. This feature is convenient for
disabling an unused channel or during an LED
short circuiting event.
Low Dropout Regulators
The AAT2847 incorporates two LDO voltage regu-
lators. The two regulators run from the same 2.7V
to 5.5V input voltage as the charge pump and have
separate ON/OFF control inputs, ENA and ENB.
For the AAT2847-EE, the LDO output voltages are
set through a resistive voltage divider from the out-
put (LDOA or LDOB) to the feedback input (FBA or
FBB). The ratio of the voltage divider resistor val-
ues determines the LDO output voltage. For the
AAT2847-QG option, LDOA is internally set to 2.8V
and LDOB is internally set to 1.5V. For the
AAT2847-QI option, LDOA is also 2.8V and LDOB
is internally set to 1.8V. Each LDO regulator can
supply a continuous load current up to 200mA, and
both LDOs include current limiting and thermal
overload protection to prevent damage to the load
or to the LDO.
Thermal Protection
The charge pump has built-in thermal protection
circuitry that will shut down the charge pump and
the LDOs if the die temperature rises above the
thermal limit, as is the case during an OUT pin
short circuit event.
Applications Information
LED Selection
The charge pump in the AAT2847 is specifically
intended for driving white LEDs. However, the
AAT2847 can drive most types of LEDs with for-
ward voltage specifications ranging from 2.0V to
4.7V. LED applications may include mixed arrange-
ments for display backlighting, color (RGB) LEDs,
infrared (IR) diodes and any other load needing a
constant current source generated from a varying
input voltage. Since the D1 to D4 constant current
channels are matched with negligible voltage
dependence, the constant current channels will be
matched regardless of the specific LED forward
voltage (V
F
) levels. Multiple channels can be com-
bined to obtain a higher LED drive current without
complication.
AAT2847-EE LDO Output Voltage
Programming
The output voltages for LDOA and LDOB are pro-
grammed by an external resistor divider network.
As shown in Figure 3, the selection of R1 and R2 is
a straightforward matter. R1 is chosen by consider-
ing the tradeoff between the feedback network bias
current and resistor value. Higher resistor values
allow stray capacitance to become a larger factor in
circuit performance, whereas lower resistor values
decrease efficiency.
Figure 3: Selection of External Resistors.
To select appropriate resistor values, first choose a
value for R1 that will produce a reasonable feed-
back network bias current. Then, according to the
desired V
LDO(A/B)
, calculate R2 according to the
equation below. An example calculation follows.
V
LDO(A/B)
R2(A/B)
V
REF
= 1.2V
R1(A/B)
LDO(A/B)
FB(A/B)
相關PDF資料
PDF描述
TQS-465AA-7R Surface Acoustic Wave Filter (SAW Filter)
TR1000 916.50 MHz Hybrid Transceiver
TR1004 914.00 MHz Hybrid Transceiver
TR1100 916.50 MHz Hybrid Transceiver
TR3001 315.00 MHz Hybrid Transceiver
相關代理商/技術參數
參數描述
TQFP 制造商:STATSCHIP 制造商全稱:STATSCHIP 功能描述:Thin Profile Quad Flat Pack
TQFP100V 制造商:ROHM 制造商全稱:Rohm 功能描述:LSI Assembly
TQFP128U 制造商:ROHM 制造商全稱:Rohm 功能描述:LSI Assembly
TQFP176U 制造商:ROHM 制造商全稱:Rohm 功能描述:LSI Assembly
TQFP48 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:48-LEAD THIN QUAD FLAT