- 您現在的位置：買賣IC網 > PDF目錄382641 > TMS370Cx2xJD (Texas Instruments, Inc.) 8-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | TMS370Cx2xJD |
| 廠商： | Texas Instruments, Inc. |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8-BIT MICROCONTROLLER |
| 中文描述： | 8位微控制器 |
| 文件頁數： | 15/54頁 |
| 文件大?。?/td> | 785K |
| 代理商： | TMS370CX2XJD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
TMS370Cx9x
8-BIT MICROCONTROLLER
SPNS036B – JANUARY 1996 – REVISED FEBRUARY 1997
15
POST OFFICE BOX 1443
HOUSTON, TEXAS 77251–1443
privileged operation and EEPROM write-protection override (continued)
The write-protect override (WPO) mode provides an external hardware method of overriding the
write-protection registers of data EEPROM on the TMS370Cx9x. Applying a 12-V input to the MC pin after the
RESET input goes high (logic 1) enters the WPO mode. The high voltage on MC during the WPO mode is not
the programming voltage for the data EEPROM or program EPROM. All EEPROM programming voltages are
generated on-chip. The WPO mode provides hardware system level capability to modify the content of the data
EEPROM while the device remains in the application, but only while requiring a 12-V external input on the MC
pin (normally not available in the end application except in a service or diagnostic environment).
low-power and IDLE modes
The TMS370Cx9x devices have two low-power modes (STANDBY and HALT) and an IDLE mode. For
mask-ROM devices, low-power modes can be disabled permanently through a programmable contact at the
time when the mask is manufactured.
The STANDBY and HALT low power modes significantly reduce power consumption by reducing or stopping
the activity of the various on-chip peripherals when processing is not required. Each of the low-power modes
is entered by executing the idle instruction when the PWRDWN/IDLE bit in register SCCR2 has been set to one.
The HALT/STANDBY bit in SCCR2 controls which low-power mode is entered.
In the STANDBY mode (HALT/STANDBY = 0), all CPU activity and most peripheral module activity is stopped;
however, the oscillator, internal clocks, and timer 1 remain active. System processing is suspended until a
qualified interrupt (hardware RESET, external interrupt on INT1, or timer 1 interrupt) is detected.
In the HALT mode (HALT/STANDBY = 1), the TMS370Cx9x is placed in its lowest power-consumption mode.
The oscillator and internal clocks are stopped, causing all internal activity to be halted. System activity is
suspended until a qualified interrupt (hardware RESET or an external interrupt on INT1) is detected. The
low-power mode selection bits are summarized in Table 9.
Table 9. Low-Power/Idle Control Bits
ááááááááááááááááá
áááááááááááááááááá
áááááááááááááááááá
áááááááááá
X = don’t care
POWER-DOWN CONTROL BITS
PWRDWN/IDLE
ááááááááá
ááááááááá
ááááááááá
áááááááá
áááááááááááááááá
á
ááááááá
á
MODE SELECTED
When low-power modes are disabled through a programmable contact in the mask-ROM devices, writing to the
SCCR2.6–7 bits is ignored. In addition, if an IDLE instruction is executed when low-power modes are disabled
To provide a method of always exiting low-power modes for mask-ROM devices, INT1 is enabled automatically
as a nonmaskable interrupt (NMI) during low-power modes when the hard watchdog mode is selected. This
means that the NMI is always generated, regardless of the interrupt enable flags.
The following information is preserved throughout both the STANDBY and HALT modes: RAM (register file),
CPU registers (stack pointer, program counter, and status register), I/O pin direction and output data, and status
registers of all on-chip peripheral functions. Since all CPU instruction processing is stopped during the
STANDBY and HALT modes, the clocking of the watchdog timer is inhibited.
相關PDF資料 |
PDF描述 |
|---|---|
| TMS370Cx2xN | 8-BIT MICROCONTROLLER |
| TMS370Cx2xNJ | 8-BIT MICROCONTROLLER |
| TMS370CX32 | 8-BIT MICROCONTROLLER |
| TMS370CX32FN | 8-BIT MICROCONTROLLER |
| TMS370CX32FZ | 8-BIT MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMS370P16A27FNQ | 制造商:Texas Instruments 功能描述: |
| TMS37112B3 WAF | 制造商:Texas Instruments 功能描述: |
| TMS37122DPWRG4 | 制造商:Texas Instruments 功能描述:3D Analog Front-end, TITL |
| TMS37145TEAIE | 制造商:Texas Instruments 功能描述: |
| TMS37145TEAIEG | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。