參數資料
型號： TMC249A
廠商： Electronic Theatre Controls, Inc.
英文描述： High Current Microstep Stepper Motor Driver with sensorless stall detection, protection / diagnostics and SPI Interface
中文描述： 大電流微步步進電機驅動器，帶有傳感器的失速檢測，保護/診斷和SPI接口
文件頁數： 12/25頁
文件大?。?/td> 219K
代理商： TMC249A
TMC249 / TMC249A DATA SHEET (V2.02 / Aug 12th, 2005)
12
Copyright 2005, TRINAMIC Motion Control GmbH & Co KG
Protection Functions
Overcurrent protection and diagnosis
The TMC249 uses the current sense resistors on the low side to detect an overcurrent: Whenever a
voltage above 0.61V is detected, the PWM cycle is terminated at once and all transistors of the bridge
are switched off for the rest of the PWM cycle. The error counter is increased by one. If the error
counter reaches 3, the bridge remains switched off for 63 PWM cycles and the error flag is read as
“active”. The user can clear the error condition in advance by clearing the error flag. The error counter
is cleared, whenever there are more than 63 PWM cycles without overcurrent. There is one error
counter for each of the low side bridges, and one for the high side. The overcurrent detection is
inactive during the blank pulse time for each bridge, to suppress spikes which can occur during
switching.
The high side comparator detects a short to GND or an overcurrent, whenever the voltage between
VS and VT becomes higher than 0.15 V at any time, except for the blank time period which is logically
ORed for both bridges. Here all transistors become switched off for the rest of the PWM cycle,
because the bridge with the failure is unknown.
The overcurrent flags can be cleared by disabling and re-enabling the chip either via the ENN pin or
by sending a telegram with both current control words set to “0000”. In high side overcurrent
conditions the user can determine which bridge sees the overcurrent, by selectively switching on only
one of the bridges with each polarity (therefore the other bridge should remain programmed to
“0000”).
Overtemperature protection and diagnosis
The circuit switches off all output power transistors during an overtemperature condition. The over-
temperature flag should be monitored to detect this condition. The circuit resumes operation after cool
down below the temperature threshold. However, operation near the overtemperature threshold
should be avoided, if a high lifetime is desired.
Overvoltage protection and ENN pin behavior
During disable conditions the circuit switches off all output power transistors and goes into a low
current shutdown mode. All register contents is cleared to “0”, and all status flags are cleared. The
circuit in this condition can also stand a higher voltage, because the voltage then is not limited by the
maximum power MOSFET voltage. The enable pin ENN provides a fixed threshold of V
CC
to allow a
simple overvoltage protection up to 40V using an external voltage divider (see schematic).
+V
M
ENN
R
μC-Port (opt.)
low=Enable,
high=Disable
R
for switch off at 26 - 29V:
at VCC=5V: R1=100K; R2=10K
at VCC=3.3V: R1=160K; R2=10K
相關PDF資料
PDF描述
TMC249A-LA High Current Microstep Stepper Motor Driver with sensorless stall detection, protection / diagnostics and SPI Interface
TMC249A-SA High Current Microstep Stepper Motor Driver with sensorless stall detection, protection / diagnostics and SPI Interface
TMC249-SA High Current Microstep Stepper Motor Driver with sensorless stall detection, protection / diagnostics and SPI Interface
TMC2601 140-370 MHz Output Frequency Digital Video Serial Transmission Encoder （8- or 10-bit Parallel Data Into Serial Format）(140-370 MHz 輸出頻率的數字視頻串行傳輸譯碼器（8位或10位并行數據轉換成串行格式）)
TMC3211 32-Bit, 20 MOPS Integer Divider(32位,20MOPS 整數除法器)
相關代理商/技術參數
參數描述
TMC249-A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:High Current Microstep Stepper Motor Driver with Sensorless Stall D e t e c t i o n ,P rotection / Diagnosis and SPI Interface
TMC249A-LA 制造商:Trinamic 功能描述:IC BRIDGE DRIVER SPI/ANLG 32QFN
TMC249A-SA 制造商:Trinamic 功能描述:STEPPER MOTOR DRIVER SMD SO-28 制造商:Trinamic 功能描述:STEPPER MOTOR DRIVER, SMD, SO-28 制造商:Trinamic 功能描述:IC MOTOR DRIVER, FULL BRIDGE, 1mA SOIC-28; Motor Type:Full Bridge; No. of Outputs:8; Output Current:1mA; Output Voltage:34V; Driver Case Style:SOIC; No. of Pins:28; Supply Voltage Min:3V; Supply Voltage Max:5.5V; MSL:MSL 2 - 1 year ;RoHS Compliant: Yes
TMC249-EVAL 制造商:Trinamic 功能描述:EVALUATION BOARD FOR TMC249
TMC249-HVHR 制造商:TRINAMIC 制造商全稱:TRINAMIC 功能描述:Evaluation Board for TMC249 with High Voltage and High Resolution
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*