- 您現在的位置：買賣IC網 > PDF目錄384999 > TMC249A-LA (Electronic Theatre Controls, Inc.) High Current Microstep Stepper Motor Driver with sensorless stall detection, protection / diagnostics and SPI Interface PDF資料下載
參數資料
| 型號： | TMC249A-LA |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | High Current Microstep Stepper Motor Driver with sensorless stall detection, protection / diagnostics and SPI Interface |
| 中文描述： | 大電流微步步進電機驅動器，帶有傳感器的失速檢測，保護/診斷和SPI接口 |
| 文件頁數： | 13/25頁 |
| 文件大?。?/td> | 219K |
| 代理商： | TMC249A-LA |
TMC249 / TMC249A DATA SHEET (V2.02 / Aug 12th, 2005)
13
Copyright 2005, TRINAMIC Motion Control GmbH & Co KG
Chopper Principle
Chopper cycle / Using the mixed decay feature
The TMC249 uses a quiet fixed frequency chopper. Both coils are chopped with a phase shift of 180
degrees. The mixed decay option is realized as a self stabilizing system (pat. fi.), by shortening the
fast decay phase, if the ON phase becomes longer. It is advised to enable the mixed decay for each
phase during the second half of each microstepping half-wave, when the current is meant to
decrease. This leads to less motor resonance, especially at medium velocities. With low velocities or
during standstill mixed decay should be switched off. In applications requiring high resolution, or using
low inductivity motors, the mixed decay mode can also be enabled continuously, to reduce the
minimum motor current which can be achieved. When mixed decay mode is continuously on or when
using high inductivity motors at low supply voltage, it is advised to raise the chopper frequency to
36kHz, because the half chopper frequency could be audible under these conditions.
oscillator clock
resp. external clock
actual current phase A
target current phase A
mixed decay disabled
mixed decay enabled
on
slow decay
on
fast decay
slow decay
When polarity is changed on one bridge, the PWM cycle on that bridge becomes restarted at once.
Fast decay switches off both upper transistors, while enabling the lower transistor opposite to the
selected polarity. Slow decay always enables both lower side transistors.
Blank Time
The TMC249 uses a digital blanking pulse for the current chopper comparators. This prevents current
spikes, which can occur during switching action due to capacitive loading, from terminating the
chopper cycle. The lowest possible blanking time gives the best results for microstepping: A long
blank time leads to a long minimum turn-on time, thus giving an increased lower limit for the current.
Please remark, that the blank time should cover both, switch-off time of the lower side transistors and
turn-on time of the upper side transistors plus some time for the current to settle. Thus the complete
switching duration should never exceed 1.5μs. With slow external power stages it will become
necessary to add additional RC-filtering for the sense resistor inputs.
The TMC249 allows to adapt the blank time to the load conditions and to the selected slope in four
steps (the effective resulting blank times are about 200ns shorter in the non-A-type):
Blank time settings
BL2
BL1
Typical blank time
GND
GND
VCC
VCC
GND 0.6 μs
VCC 0.9 μs
GND 1.2 μs
VCC 1.5 μs
相關PDF資料 |
PDF描述 |
|---|---|
| TMC249A-SA | High Current Microstep Stepper Motor Driver with sensorless stall detection, protection / diagnostics and SPI Interface |
| TMC249-SA | High Current Microstep Stepper Motor Driver with sensorless stall detection, protection / diagnostics and SPI Interface |
| TMC2601 | 140-370 MHz Output Frequency Digital Video Serial Transmission Encoder （8- or 10-bit Parallel Data Into Serial Format）(140-370 MHz 輸出頻率的數字視頻串行傳輸譯碼器（8位或10位并行數據轉換成串行格式）) |
| TMC3211 | 32-Bit, 20 MOPS Integer Divider(32位,20MOPS 整數除法器) |
| TMC428 | Intelligent Triple Stepper Motor Controller with Serial Peripheral Interfaces |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMC249A-SA | 制造商:Trinamic 功能描述:STEPPER MOTOR DRIVER SMD SO-28 制造商:Trinamic 功能描述:STEPPER MOTOR DRIVER, SMD, SO-28 制造商:Trinamic 功能描述:IC MOTOR DRIVER, FULL BRIDGE, 1mA SOIC-28; Motor Type:Full Bridge; No. of Outputs:8; Output Current:1mA; Output Voltage:34V; Driver Case Style:SOIC; No. of Pins:28; Supply Voltage Min:3V; Supply Voltage Max:5.5V; MSL:MSL 2 - 1 year ;RoHS Compliant: Yes |
| TMC249-EVAL | 制造商:Trinamic 功能描述:EVALUATION BOARD FOR TMC249 |
| TMC249-HVHR | 制造商:TRINAMIC 制造商全稱:TRINAMIC 功能描述:Evaluation Board for TMC249 with High Voltage and High Resolution |
| TMC249-SA | 制造商:Trinamic 功能描述:IC TMC249-SA SO-28 |
發布緊急采購，3分鐘左右您將得到回復。