參數資料
型號： THS6062D
廠商： Texas Instruments, Inc.
英文描述： LOW-NOISE ADSL DUAL DIFFERENTIAL RECEIVER
中文描述： 低噪聲寬帶雙差分接收機
文件頁數： 26/31頁
文件大?。?/td> 540K
代理商： THS6062D
THS6062
LOW-NOISE ADSL DUAL DIFFERENTIAL RECEIVER
SLOS228B – JANUARY 1999 – REVISED JUNE 1999
26
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
general PowerPAD design considerations
1.
Prepare the PCB with a top side etch pattern as shown in Figure 47. There should be etch for the leads as
well as etch for the thermal pad.
2.
Place five holes in the area of the thermal pad. These holes should be 13 mils in diameter. They are kept
small so that solder wicking through the holes is not a problem during reflow.
3.
Additional vias may be placed anywhere along the thermal plane outside of the thermal pad area. This helps
dissipate the heat generated by the THS6062DGN IC. These additional vias may be larger than the 13-mil
diameter vias directly under the thermal pad. They can be larger because they are not in the thermal pad
area to be soldered so that wicking is not a problem.
4.
Connect all holes to the internal ground plane.
5.
When connecting these holes to the ground plane,
do
not
use the typical web or spoke via connection
methodology. Web connections have a high thermal resistance connection that is useful for slowing the heat
transfer during soldering operations. This makes the soldering of vias that have plane connections easier.
In this application, however, low thermal resistance is desired for the most efficient heat transfer. Therefore,
the holes under the THS6062DGN package should make their connection to the internal ground plane with
a complete connection around the entire circumference of the plated-through hole.
6.
The top-side solder mask should leave the terminals of the package and the thermal pad area with its five
holes exposed. The bottom-side solder mask should cover the five holes of the thermal pad area. This
prevents solder from being pulled away from the thermal pad area during the reflow process.
7.
Apply solder paste to the exposed thermal pad area and all of the IC terminals.
8.
With these preparatory steps in place, the THS6062DGN IC is simply placed in position and run through
the solder reflow operation as any standard surface-mount component. This results in a part that is properly
installed.
The actual thermal performance achieved with the THS6062DGN in its PowerPAD package depends on the
application. In the example above, if the size of the internal ground plane is approximately 3 inches
×
3 inches,
then the expected thermal coefficient,
θ
JA
,
is
about 58.4
°
C/W. For comparison, the non-PowerPAD version of
the THS6062 IC (SOIC) is shown. For a given
θ
JA
, the maximum power dissipation is shown in Figure 48 and
is calculated by the following formula:
PD
TMAX–TA
JA
Where:
P
D
T
MAX
= Absolute maximum junction temperature (150
°
C)
T
A
= Free-ambient air temperature (
°
C)
θ
JA
=
θ
JC
+
θ
CA
θ
JC
= Thermal coefficient from junction to case
θ
CA
= Thermal coefficient from case to ambient air (
°
C/W)
= Maximum power dissipation of THS6062 IC (watts)
相關PDF資料
PDF描述
THS6062DGN LOW-NOISE ADSL DUAL DIFFERENTIAL RECEIVER
THS6062EVM RECTIFIER SCHOTTKY 5A30V DO201AD
THS6072D LOW-POWER ADSL DIFFERENTIAL RECEIVER
THS6072DGN LOW-POWER ADSL DIFFERENTIAL RECEIVER
THS6072EVM LOW-POWER ADSL DIFFERENTIAL RECEIVER
相關代理商/技術參數
參數描述
THS6062DGN 制造商:TI 制造商全稱:Texas Instruments 功能描述:LOW-NOISE ADSL DUAL DIFFERENTIAL RECEIVER
THS6062EVM 功能描述:其他開發工具 THS6062 Eval Mod RoHS:否 制造商:Parallax 產品:ELEV-8 Hex Upgrade Kits 類型:Robotics 工具用于評估:ELEV-8 Quadcopter 工作電源電壓:
THS6062ID 功能描述:緩沖器和線路驅動器 High Speed RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel
THS6062IDG4 功能描述:緩沖器和線路驅動器 High Speed RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel
THS6062IDGN 功能描述:緩沖器和線路驅動器 High Speed RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*