- 您現在的位置：買賣IC網 > PDF目錄225295 > TDA8006 (NXP Semiconductors N.V.) Multiprotocol IC Card Coupler(多協議的IC卡耦合器) PDF資料下載
參數資料
| 型號： | TDA8006 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Multiprotocol IC Card Coupler(多協議的IC卡耦合器) |
| 中文描述： | 多協議IC卡器（多協議的集成電路卡耦合器） |
| 文件頁數： | 14/40頁 |
| 文件大?。?/td> | 166K |
| 代理商： | TDA8006 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
2000 Feb 21
21
Philips Semiconductors
Product specication
Multiprotocol IC Card coupler
TDA8006
handbook, full pagewidth
MGR234
P4
P40
CLK
EN
I/O
R/W
FF
read
write
Fig.10 Using synchronous cards.
EXTRA GUARD TIME
Between the transmission of two characters to the card,
the ISO 7816 UART automatically inserts a number of
guard ETUs equal to the value, called GT, stored in the
GTR, see Table 10. For a GT of FAH, for example, the
value would be 1111 1010 reading from D7 to D0.
A GT of FFH has a special status which means 0 ETU
when the protocol is T = 0 and
1 ETU when the protocol
is T = 1 (reception and transmission is possible at
11 ETU).
Table 10 Guard Time Register (GTR; address 6; write only; all bits cleared after reset)
D7
D6
D5
D4
D3
D2
D1
D0
GUARD TIME VALUE (GT)
n7
n6
n5
n4
n3
n2
n1
n0
n7n6n5n4 n3n2n1n0
UART receive and transmit registers
UART Receive Register (URR; address 4; read only; all
bits cleared after reset)
D7 to D0 are the data bits received from the card.
Because the UART automatically converts the characters
according to the convention recognized during TS, all
characters in the URR are in direct convention.
The received character is loaded in the URR 0.5 ETU
after the parity shift, i.e. 10.5 ETU after the edge of the
start bit. This overwrites the previous character which
should have been read by the controller.
The UART checks the parity of the received characters;
if the parity is wrong, then bit PE is set in the status
register at the same time as bit RBF (Receive Buffer
Full).
In protocol T = 0, I/O is pulled LOW between
10.5 and 11.75 ETU in case of error. Characters may be
received from the card every 12 ETU, even after a
transmission (see LCT; Table 9). In protocol T = 1,
reception is possible at 11 ETU.
相關PDF資料 |
PDF描述 |
|---|---|
| TDS10 | SLIDE DIP SWITCH-10SWITCHES, SP3T, LATCHED,0.025A, 24VDC, THROUGH HOLE-STRAIGHT |
| TDSG3160 | 7 SEG NUMERIC DISPLAY |
| TDSY5160 | 7 SEG NUMERIC DISPLAY |
| TE-11211 | TOGGLE SWITCH, DPDT, LATCHED, 5A, 28VDC, PANEL MOUNT-THREADED |
| TE5D-12.8MHZ | TCVCXO, CLOCK, 12.8 MHz, HCMOS OUTPUT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8006AH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multiprotocol IC Card coupler |
| TDA8006AH/C1 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multiprotocol IC Card coupler |
| TDA8006AH/C2 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multiprotocol IC Card coupler |
| TDA8006AH/C3 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multiprotocol IC Card coupler |
| TDA8006AH/C325,518 | 功能描述:輸入/輸出控制器接口集成電路 ONE CHIP SMART CARD INTERFACE RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。