參數資料
型號： TDA8006
廠商： NXP Semiconductors N.V.
英文描述： Multiprotocol IC Card Coupler(多協議的IC卡耦合器)
中文描述： 多協議IC卡器（多協議的集成電路卡耦合器）
文件頁數： 11/40頁
文件大小： 166K
代理商： TDA8006
2000 Feb 21
19
Philips Semiconductors
Product specication
Multiprotocol IC Card coupler
TDA8006
handbook, full pagewidth
MGR232
I/O
SS
RIU
CMDVCC
P4
FF
R/W
EN
INT
FSD
RBF
release reset
set start session
set CMDVCC
first start
read status
int cleared
anything
buffer full
read status
read character
and int cleared
reset start session
10.5 ETU
Fig.8 First character reception.
TRANSMISSION
Transmission mode is selected when TRN is HIGH.
If enabled, an interrupt occurs on the rising edge of TRN,
indicating that the transmission buffer is empty and ready
to accept a character for transmission. The interrupt is
cleared during the read status operation. The character is
written to the UTR on the falling edge of EN during the
write operation, and starts to be transmitted on the rising
edge of EN.
The I/O line is read at 10.84 ETU to check if the card has
detected a parity error. At the same time, bit TBE is set in
the USR, and, if enabled, an interrupt occurs to indicate
that the transmission buffer is empty, and that a new
character may be written. If the parity is correct, the
transmission of the next character will start at
12 ETU + GT + 0.5 ETU after the start bit of the previous
character (see Section “Extra guard time”). If the parity is
not correct, then assuming that a character has been
written to the UTR, the transmission starts at 13 ETU (the
guard time GT must be programmed before transmitting).
Bit LCT can be used for cards that are required to change
from transmission to reception mode very fast. If LCT is set
HIGH, then the UART automatically resets
bits TRN and LCT at 10.85 ETU if no parity error has
occurred; the UART is ready to receive a character from
the card at 12 ETU (T = 0) or 11 ETU (T = 1) after the
previous start bit. If a parity error has occurred during
transmission of the last character, then the UART stays in
transmission mode with LCT set, waiting for the software
to rewrite the corrupted character.
相關PDF資料
PDF描述
TDS10 SLIDE DIP SWITCH-10SWITCHES, SP3T, LATCHED,0.025A, 24VDC, THROUGH HOLE-STRAIGHT
TDSG3160 7 SEG NUMERIC DISPLAY
TDSY5160 7 SEG NUMERIC DISPLAY
TE-11211 TOGGLE SWITCH, DPDT, LATCHED, 5A, 28VDC, PANEL MOUNT-THREADED
TE5D-12.8MHZ TCVCXO, CLOCK, 12.8 MHz, HCMOS OUTPUT
相關代理商/技術參數
參數描述
TDA8006AH 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multiprotocol IC Card coupler
TDA8006AH/C1 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multiprotocol IC Card coupler
TDA8006AH/C2 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multiprotocol IC Card coupler
TDA8006AH/C3 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multiprotocol IC Card coupler
TDA8006AH/C325,518 功能描述:輸入/輸出控制器接口集成電路 ONE CHIP SMART CARD INTERFACE RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*