參數資料
型號： TDA8005
廠商： NXP Semiconductors N.V.
英文描述： Low-Power Smart Card Coupler(低功耗智能卡藕合器)
中文描述： 低功耗智能卡器（低功耗智能卡藕合器）
文件頁數： 2/32頁
文件大小： 198K
代理商： TDA8005
1996 Sep 25
10
Philips Semiconductors
Product specication
Low-power smart card coupler
TDA8005
Fig.4 Supply supervisor.
handbook, full pagewidth
MBH634
Vth1 + Vhys1
Vth1
V
DD
Vth2
VDEL
ALARM
Low impedance supply (pin LIS)
For some applications, it is mandatory that the contacts to
the card (VCC, RST, CLK and I/O) are low impedance while
the card is inactive and also when the coupler is not
powered. An auxiliary supply voltage on pin LIS ensures
this condition where ILIS =<5 A for VLIS = 5 V. This low
impedance situation is disabled when VCC starts rising
during activation, and re-enabled when the step-up
converter is stopped during deactivation. If this feature is
not required, the LIS pin must be tied to VDD.
Step-up converter
Except for the VCC generator, and the other cards contacts
buffers, the whole circuit is powered by VDDD and VDDA.
If the supply voltage is 3 V or 5 V, then a higher voltage is
needed for the ISO contacts supply. When a card session
is requested by the controller, the sequencer first starts the
step-up converter, which is a switched capacitors type,
clocked by an internal oscillator at a frequency
approximately 2.5 MHz. The output voltage, VUP, is
regulated at approximately 6,5 V and then fed to the VCC
generator. VCC and GND are used as a reference for all
other cards contacts. The step-up converter may be
chosen as a doubler or a tripler by mask option, depending
on the voltage and the current needed on the card.
ISO 7816 security
The correct sequence during activation and deactivation of
the card is ensured through a specific sequencer, clocked
by a division ratio of the internal oscillator.
Activation (START signal P05) is only possible if the card
is present (PRES HIGH or LOW according to mask
option), and if the supply voltage is correct (ALARM signal
inactive), CLK and RST are controlled by RSTIN (P04),
allowing the correct count of CLK pulses during
Answer-to-Reset from the card.
The presence of the card is signalled to the controller by
the OFF signal (P10).
During a session, the sequencer performs an automatic
emergency deactivation in the event of card take-off,
supply voltage drop, or hardware problems. The OFF
signal falls thereby warning the controller.
相關PDF資料
PDF描述
TDA8006 Multiprotocol IC Card Coupler(多協議的IC卡耦合器)
TDS10 SLIDE DIP SWITCH-10SWITCHES, SP3T, LATCHED,0.025A, 24VDC, THROUGH HOLE-STRAIGHT
TDSG3160 7 SEG NUMERIC DISPLAY
TDSY5160 7 SEG NUMERIC DISPLAY
TE-11211 TOGGLE SWITCH, DPDT, LATCHED, 5A, 28VDC, PANEL MOUNT-THREADED
相關代理商/技術參數
參數描述
TDA8005A 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low-power 3 V/5 V smart card coupler
TDA8005AG 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low-power 3 V/5 V smart card coupler
TDA8005AH 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low-power 3 V/5 V smart card coupler
TDA8005G 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low-power smart card coupler
TDA8005H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low-power smart card coupler
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*