參數資料
型號: TCF5600
廠商: MOTOROLA INC
元件分類: 穩壓器
英文描述: CONNECTOR ACCESSORY
中文描述: 1 A SWITCHING CONTROLLER, PDIP18
封裝: PLASTIC, DIP-18
文件頁數: 9/12頁
文件大?。?/td> 206K
代理商: TCF5600
TCA5600 TCF5600
APPLICATIONS INFORMATION
(See Figure 18)
9
MOTOROLA ANALOG IC DEVICE DATA
Voltage Reference (Vref)
The voltage reference Vref is based upon a highly stable
bandgap voltage reference and is accessible on Pin 5 for
additional tasks. This circuit part has its own supply
connection on Pin 3 and is, therefore, able to operate in
standby mode. The RC network R3, C6 improves the ripple
rejection on both regulators.
DC/DC Converter
The dc/dc converter performs according to the flyback
principle and does not need a time base circuit. The
maximum coil current is well defined by means of the current
sensing resistor R1 under all working conditions (startup
phase, circuit overload, wide supply voltage range and
extreme load current change). Figure 13 shows the Simplified
Converter Schematic.
Figure 13. Simplified Converter Schematic
VCC2
L1
300
μ
H
10
Control Feedback
V12(H)
V12(L)
+
VF
Prog.
Regulator
8
Vout2
C3
47nF
R5
10k
C7
0.22
μ
F
9
VCE(sat)
C2
100
μ
F
12
R1
0.68
Comp
+
R4
85K
7
A simplified method on “how to calculate the coil inductance”
is given below. The operation point at minimum supply
voltage (VCC2) and max. output current (Iout2) for a fixed
output voltage (Vout2) determines the coil data. Figure 14
shows the typical voltage and current waveforms on the coil
L1 (coil losses neglected).
Equations (1) and (2) yield the respective coil voltage
VL– and VL + (see Figure 14):
VL+ = Vout2 +
V(Pin 9 – Pin 8) + VF – VCC2
VL– = VCC2 – VCE(sat) – V12(H)
(1)
(2)
[
V(Pin 9 – Pin 8): input/output voltage drop of the regulator,
2.5 V typical]
[VF, VCE(sat), V12(H): see Electrical Characteristics Table]
The time ratio
α
for the charging time to dumping time is
defined by Equation (3):
α
=
t1
t2
VL+
VL–
=
(3)
éé
éé
éé
éééé
ééé
Coil
Voltage
VCC2
t
t
t2
Coil
Current
ILpeak
t1
+
L
V
L
V
Figure 14. Voltage and Current Waveform
on the Coil
(not to scale)
The coil charging time t1 is found using Equation (4):
(4)
t1 =
1
(1 +1
α
)
f
[f : minimum oscillation frequency which should be chosen
above the audio frequency band (e.g. 20 kHz)]
Knowing the dc output current Iout2 of the programmable
regulator, the peak coil current IL(peak) can now be calculated:
IL(peak) = 2
(Iout2) (1 +
α
)
(5)
The coil inductance L1 of the nonsaturated coil is given by
Equation (6):
(6)
L1 =
(VL–)
t1
IL(peak)
The formula (6a) yields the current sensing resistor R1 for a
defined peak coil current IL(peak):
V12(H)
IL(peak)
(6a)
R1 =
In order to limit the by–pass current through capacitor C7
during the energy dumping phase the value C2>>C7 should
be implemented.
For all other operation conditions, the feedback signal from
the programmable voltage regulator controls the activity of
the converter.
相關PDF資料
PDF描述
TCA650 CHROMINANCE DEMODULATOR FOR SECAM OR PAL / SECAM DECODERS
TCA750 Multi-stabilizer for electronic tuning
TCA940 AF AMPLIFIER AMPLIFICATEUR BF
TCA940E AF AMPLIFIER AMPLIFICATEUR BF
TCA955 SPEED CONTROLLER
相關代理商/技術參數
參數描述
TCF6 功能描述:保險絲 600V 6A Time Delay Finger Safe Ind RoHS:否 制造商:Littelfuse 產品:Surface Mount Fuses 電流額定值:0.5 A 電壓額定值:600 V 保險絲類型:Fast Acting 保險絲大小/組:Nano 尺寸:12.1 mm L x 4.5 mm W 安裝風格: 端接類型:SMD/SMT 系列:485
TCF60 功能描述:保險絲 600V 60A Time Delay Finger Safe Ind RoHS:否 制造商:Littelfuse 產品:Surface Mount Fuses 電流額定值:0.5 A 電壓額定值:600 V 保險絲類型:Fast Acting 保險絲大小/組:Nano 尺寸:12.1 mm L x 4.5 mm W 安裝風格: 端接類型:SMD/SMT 系列:485
TCF6000 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:PERIPHERAL CLAMPING ARRAY
TCF6000D 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:PERIPHERAL CLAMPING ARRAY
TCF60RN 功能描述:保險絲 CUBEFUSE 60A NON-INP RoHS:否 制造商:Littelfuse 產品:Surface Mount Fuses 電流額定值:0.5 A 電壓額定值:600 V 保險絲類型:Fast Acting 保險絲大小/組:Nano 尺寸:12.1 mm L x 4.5 mm W 安裝風格: 端接類型:SMD/SMT 系列:485