- 您現在的位置：買賣IC網 > PDF目錄384958 > TCA440 (SIEMENS AG) AM Receiver Circuit PDF資料下載
參數資料
| 型號： | TCA440 |
| 廠商： | SIEMENS AG |
| 英文描述： | AM Receiver Circuit |
| 中文描述： | AM接收電路 |
| 文件頁數： | 11/11頁 |
| 文件大?。?/td> | 73K |
| 代理商： | TCA440 |
Application hints
The PCB is to arrange such that there are maximum ground lines (ground area) voltage supply has to be blocked
to ground by a capacitor of 10...100 nF in order to avoid distortions. Blocking should be as close as possible to
the circuit.
The RF circuit has to layout such that 150 mV
(rms)
oscillator voltage are applied to pin 5. Symmetrically applying
an external oscillator is possible to pin 4 or pin 5. The unused input must be connected to ground via capacitor
and in the same time be connected to supply voltage at pin 6.
It is recommendable to profide off earth connections 1 and 3, because in this way common - mode interferences
more effectively can be suppessed. Single - sided capacitive control of pin 1 and 2 is possible, the unused input
must be connected to ground via capacitor.
Mixer outputs 15 and 16 can be used equivalently.
Load resistances of the mixer (IF selection) at pin 15 respectively pin 16 should run to approximately 7 k
.
To avoid saturation of the multiplier the maximum peak voltage occuring during operation should not exceed the
level (V
CC
- 3 V) IF response to voltage from pin 15 respectively pin 16 to pin 12 should be approximately - 18 dB
that the control characteristics of IF - and RF - part optimally be matched.
Peak voltage at pin 7 occuring during operation should not exceed 2 V that the IF output does not go into
saturation.
All the RF bypass capacitors should amount to 100 nF. Sufficient decoupling of wavemagnet and oscillator coil is
to be taken into consideration.
All components and parts must be carefully proportioned in order to obtain optimum wise characteristics.
Wavemagnets applied should so much mass as possible. The transformation ratio of the input circuitry should run
to 10...12.
In order to improve RF response characteristic a RF preselector can be additionally preceded or the wavemagnet
can be tighty coupled by means of an emitter follower impedance transformer.
Improvement of signal - to - noise ratio at average input voltages can be obtained by delayed control of the RF
part. Control should be start at approximately 1...2 mV.
V
goHF
TCA 440 T
~
4
5
6
2
1
3
8
11
13
9
7
14
15
12
10
16
S3
330p
±
W1a
W1b
-20%
RG
1.8k
±
2%
20
μ
±
20%
8.2k
±
+50%
4.7
μ
±
50%
S1
100
±
2%
W1
Rp3
1.5n
±
x
A
12k
±
2%
+50%
4.7
μ
±
50%
V
AF
+V
CC
1.5n
±
Rp2
W1
+50%
W2
1.5k
±
2%
+50%
25
≤
RG
≤
100
47
μ
±
50%
+50%
39k
±
2%
S2
TCA 440 T
12/95
TCA 440 / T
11
Reprinting is generally permitted, indicating the source. However, our consent must be obtained in all cases.
SMI reserves the right to make changes in specifications at any time and without notice.
The information and suggestions are given without obligation and cannot given rise to any liability, they do not indicate the
availability of the components mentioned.
The information included herein is believed to be accurate and reliable. However, the SMI assumes no responsibility for its use; nor
for any infringements of patents or of other rights of third parties which may result from its use.
相關PDF資料 |
PDF描述 |
|---|---|
| TCA440T | AM - Receiver Circuit |
| TCA4500A | STEREO DECODER |
| TCA520B | OPERATIONAL AMPLIFIER |
| TCA520D | OPERATIONAL AMPLIFIER |
| TCA530 | INTEGRATED VOLTAGE STABILIZER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TCA440T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:AM - Receiver Circuit |
| TCA4500A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:STEREO DECODER |
| TCA4511 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Stereo demodulator for car-and mains operated radios |
| TCA4511-2 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PLL Stereo decoder |
| TCA5013ZAHR | 功能描述:Smart Card Interface 48-NFBGA (5x5) 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:有效 應用:智能卡 接口:I2C 電壓 - 電源:2.7 V ~ 5.5 V 封裝/外殼:48-TFBGA 供應商器件封裝:48-NFBGA（5x5） 安裝類型:表面貼裝 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。