參數資料
型號： TC647EPA
廠商： Microchip Technology Inc.
英文描述： PWM Fan Speed Controller with FanSense Technology
中文描述： 與FanSense PWM風扇速度控制器技術
文件頁數： 10/28頁
文件大?。?/td> 478K
代理商： TC647EPA
TC647
DS21447C-page 10
2002 Microchip Technology Inc.
5.1
Temperature Sensor Design
The temperature signal connected to V
IN
must output a
voltage in the range of 1.25V to 2.65V (typical) for 0%
to 100% of the temperature range of interest. The
circuit in Figure 5-2 illustrates a convenient way to
provide this signal.
FIGURE 5-2:
Circuit.
Temperature Sensing
Figure 5-2 illustrates a simple temperature dependent
voltage divider circuit. RT
1
is a conventional 100 k
@
25°C NTC thermistor, while R
1
and R
2
are standard
resistors. The supply voltage, V
DD
, is divided between
R
2
and the parallel combination of RT
1
and R
1
(for con-
venience, the parallel combination of RT
1
and R
1
will
be referred to as R
TEMP
). The resistance of the ther-
mistor at various temperatures is obtained from the
manufacturer’s specifications. Thermistors are often
referred to in terms of their resistance at 25°C. Gener-
ally, the thermistor shown in Figure 5-2 is a non-linear
device with a negative temperature coefficient (also
called an NTC thermistor). In Figure 5-2, R
1
is used to
linearize the thermistor temperature response and R
2
is used to produce a positive temperature coefficient at
the V
IN
node. As an added benefit, this configuration
produces an output voltage delta of 1.4V, which is well
within the range of the V
C(SPAN)
specification of the
TC647. A 100 k
NTC thermistor is selected for this
application in order to keep I
DIV
at a minimum.
For the voltage range at V
IN
to be equal to 1.25V to
2.65V, the temperature range of this configuration is
0°C to 50°C. If a different temperature range is required
from this circuit, R
1
should be chosen to equal the
resistance value of the thermistor at the center of this
new temperature range. It is suggested that a maxi-
mum temperature range of 50°C be used with this cir-
cuit due to thermistor linearity limitations. With this
change, R
2
is adjusted according to the following
equations:
EQUATION
These two equations facilitate solving for the two
unknown variables, R
1
and R
2
. More information about
Thermistors may be obtained from AN679,
“Tempera-
ture Sensing Technologies”
, and AN685,
“Thermistors
in Single Supply Temperature Sensing Circuits”
, which
can be downloaded from Microchip’s website at
www.microchip.com.
5.2
Minimum Fan Speed
A voltage divider on V
MIN
sets the minimum PWM duty
cycle and, thus, the minimum fan speed. As with the
V
IN
input, 1.25V to 2.65V corresponds to 0% to 100%
duty cycle. Assuming that fan speed is linearly related
to duty cycle, the minimum speed voltage is given by
the equation:
EQUATION
For example, if 2500 RPM equates to 100% fan speed,
and a minimum speed of 1000 RPM is desired, then
the V
MIN
voltage is:
EQUATION
The V
MIN
voltage may be set using a simple resistor
divider as shown in Figure 5-3. Per Section 1.0,
“Electrical Characteristics”, the leakage current at the
V
MIN
pin is no more than 1 μA. It would be very
conservative to design for a divider current, I
DIV
, of
100 μA. If V
DD
= 5.0V then;
EQUATION
R2 = 23.2 k
R1 = 100 k
RT1
NTC
Thermistor
100 k
@ 25oC
I
DIV
V
IN
V
DD
V
DD
x R
2
R
TEMP
(T
1
) + R
2
= V(T
1
)
R
TEMP
(T
2
) + R
2
= V(T
2
)
V
DD
x R
2
Where T
1
and T
2
are the chosen temperatures and
R
TEMP
is the parallel combination of the thermistor
and R
1
.
Minimum Speed
Full Speed
V
MIN
=
x (1.4V) + 1.25V
1000
2500
V
MIN
=
x (1.4V) + 1.25V = 1.81V
R
1
+ R
2
I
DIV
= 1e
–4
A = 5.0V
R
1
+ R
2
= 5.0V
= 50 k
1e
–4
A
相關PDF資料
PDF描述
TC647EUA PWM Fan Speed Controller with FanSense Technology
TC648VOA Fan Speed Controller with Auto-Shutdown and Over-Temperature Alert
TC648 Fan Speed Controller with Auto-Shutdown and Over-Temperature Alert
TC648E Fan Speed Controller with Auto-Shutdown and Over-Temperature Alert
TC648VPA Fan Speed Controller with Auto-Shutdown and Over-Temperature Alert
相關代理商/技術參數
參數描述
TC647EUA 功能描述:馬達/運動/點火控制器和驅動器 w/Fault Dtct RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
TC647EUATR 功能描述:馬達/運動/點火控制器和驅動器 w/Fault Dtct RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
TC647VOA 功能描述:馬達/運動/點火控制器和驅動器 w/Fault Dtct RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
TC647VOA 制造商:Microchip Technology Inc 功能描述:Fan Management Controller IC Package/Cas
TC647VOATR 功能描述:馬達/運動/點火控制器和驅動器 w/Fault Dtct RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*