- 您現在的位置：買賣IC網 > PDF目錄372368 > STV2001 (意法半導體) I2C SINGLE FREQUENCY DEFLECTION PROCESSOR AND 120 MHz RGB PREAMPLIFIER PDF資料下載
參數資料
| 型號： | STV2001 |
| 廠商： | 意法半導體 |
| 英文描述： | I2C SINGLE FREQUENCY DEFLECTION PROCESSOR AND 120 MHz RGB PREAMPLIFIER |
| 中文描述： | 撓度的I2C單頻處理器和120兆赫的RGB前置放大器 |
| 文件頁數： | 29/46頁 |
| 文件大?。?/td> | 528K |
| 代理商： | STV2001 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
STV2001
29/
46
The gain of this stage can be adjusted (
±
25%) de-
pending on its register value.
The mean value of this ramp is driven by its own
I
2
C register (vertical position) with :
VPOS = 7/16 x
V
REF-V
=
±
300 mV.
Usually V
OUT
is sent through a resistive divider to
the inverting input of the booster. Since VPOS de-
rives from V
REF-V
,
the bias voltage sent to the non-
inverting input of the booster should also derive
from V
REF-V
to optimize the accuracy
(see
Figure 14
).
Figure 14. AGC Loop Block Diagram
14.3.3 - Basic Equations
As a first approximation, the amplitude of the ramp
on Pin 7 (VOUT) is calculated as follows:
V
OUT
- VPOS = (V
OSC
- V
DCMID
) x
(1 + 0.25 (V
AMP
))
where :
V
DCMID
= 7/16 x V
REF
(middle value of the ramp on
Pin 5, typically 3.6V)
V
OSC
= V
5
(ramp with fixed amplitude)
V
AMP
= -1 as minimum vertical amplitude register
value and +1 as maximum value.
VPOS is calculated according to:
VPOS = V
DCMID
+ (0.4x V
P
)
where V
P
= -1 and +1 as respectively minimum
and maximum vertical position register value.
The current available on Pin 6 is:
I
OSC
=
where
C
OSC
= capacitor connected on Pin 6
f = synchronization frequency.
x V
REF
x C
OSC
x
f
14.3.4 - Geometric Corrections
The principle is represented in
Figure 15
.
Starting from the vertical ramp, a parabola-shaped
current is generated for E/W correction (also
known as Pin Cushion correction), dynamic hori-
zontal phase control correction.
The parabola generator consists of an analog mul-
tiplier, the output current of which is equal to :
I = k x
(
V
OUT
-
V
DCMID
)
2
where V
OUT
is the vertical output ramp (typically
between 2 and 5 V) and V
DCMID
is 3.6 V
(for V
REF-V
= 8.2V). The VOUT sawtooth is typical-
ly centered on 3.6 V. By changing the vertical po-
sition, the sawtooth shifts by
±
0.4 V.
The "geometry tracking" feature ensures a correct
screen geometry for any end user adjustment. It
generates non-symmetric parabola dependent on
the vertical position. To avoid Vertical EHT com-
pensation (VBreathing) from affecting the geome-
try correction, an additional Buffer Amplifier is
used for VBreathing.
4
VSYNCIN
2
SYNCHRO
OSCILLATOR
DISCH.
OSC
CAP
6
CHARGE CURRENT
TRANSCONDUCTANCE
AMPLIFIER
SAMPLING
CAPACITANCE
S CORRECTION
BREATH
VOUT
VPOSITION
SUB09/7bits
VERT AMP
SUB08/7bits
VS AMP
SUB0A/7bits
SAMPLING
Vlow
Sawth
Disch
.
REF
24
7
I2C
sub14
/6bits
3
8
相關PDF資料 |
PDF描述 |
|---|---|
| STV2100 | TV/Video Signal Processor |
| STV2112 | Color Decoder Circuit |
| STV2116 | Low Current Operation at 250 ，Low Reverse Leakage,Low Noise Zener Diode |
| STV2118A | Low Current Operation at 250 ，Low Reverse Leakage,Low Noise Zener Diode |
| STV2151B | Low Current Operation at 250 ，Low Reverse Leakage,Low Noise Zener Diode |
相關代理商/技術參數 |
參數描述 |
|---|---|
| STV200K-10Y | 制造商:Sola/Hevi-Duty 功能描述: |
| STV200K-27Y | 制造商:Sola/Hevi-Duty 功能描述: |
| STV200N55F3 | 功能描述:MOSFET N-channel 55 V RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
| STV-201-1 | 制造商:TE Connectivity 功能描述: |
| STV202 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TV Power Schematic |
發布緊急采購，3分鐘左右您將得到回復。