- 您現在的位置：買賣IC網 > PDF目錄372330 > STF203-22.TC SUPPRESSOR CIRCUIT|TSSOP|6PIN|PLASTIC PDF資料下載
參數資料
| 型號： | STF203-22.TC |
| 英文描述： | SUPPRESSOR CIRCUIT|TSSOP|6PIN|PLASTIC |
| 中文描述： | 抑癌電路| TSSOP封裝| 6針|塑料 |
| 文件頁數： | 4/7頁 |
| 文件大?。?/td> | 134K |
| 代理商： | STF203-22.TC |
4
2001 Semtech Corp.
www.semtech.com
PROTECTION PRODUCTS
Applications Information
STF201-22 & STF201-30
Figure 1 - STF201 Circuit Diagram
Device Connection
The STF201 is designed to provide termination, EMI
filtering and ESD protection for two USB I/O lines. The
equivalent circuit diagram is shown in Figure 1. The
device is connected as follows:
USB data lines are routed through the STF201 for
easy implementation and optimum pc board layout.
Pin 1 is connected to the voltage supply line. The
input of the D+ line is routed into pin 2 and out of
pin 5. The input of the D- line is connected at pin 3
and the output at pin 4. Pin 6 is connected to
ground. The ground connection should be made
directly to the ground plane for best results. The
path length is kept as short as possible to reduce
the effects of parasitic inductance in the board
traces.
"
USB Port Design Considerations
The Universal Serial Bus (USB) specification requires
termination and filtering components for proper opera-
tion. In addition, an open USB socket is vulnerable to
hazardous ESD discharges in excess of 15kV. These
discharges can may occur on the data lines or the
voltage bus. The STF201 is an easily implemented
solution designed to meet the termination & EMI filter
requirements of the USB specification revision 1.1. It
also provides ESD protection to IEC 61000-4-2, level
4.
A simplified USB port is shown in Figure 3. USB line
termination is achieved with series resistors on both
the D+ and D- lines. These resistors preserve signal
integrity by matching the cable impedance to that of
the differential driver. 15k
pull-down resistors are
used to identify a downstream port while an upstream
port is identified with a 1.5K
pull up resistor on either
the D+ (full speed devices) or the D- (low speed de-
vices) data line. Capacitors are used to bypass high
frequency energy to ground and for edge rate control
of the USB signals. TVS diodes are added for ESD
protection of both (D+ & D-) data lines and the voltage
bus (V
). A power distribution switch and voltage
regulator provide the power management functions of
the port.
Semtech provides a complete solution to simplify USB
port design (Figure 4). The STF201 & STF202 inte-
Figure 2 - STF201 Connection Diagram
1
2
3
4
5
6
grate all of the components necessary for line termina-
tion, bidirectional EMI filtering, and ESD protection on
downstream (STF201) or upstream (STF202) ports.
The SC5826 is a dual port power switch that provides
individual or ganged port switching, fault reporting, and
inrush current limiting as required by the USB specifica-
tion. The SC5205 ULDO provides a stable voltage to
the USB controller.
Board Placement & layout Guidelines.
Board layout and placement of the STF201 play a
critical role in EMI & ESD suppression. Designing a
USB hub to meet EMI & ESD immunity requirements
requires a combination of optimum component place-
ment, trace routing, and good circuit design practices.
Some general guidelines are given below:
Avoid running D+ & D- signal line traces near high
speed clock lines or similar signal lines.
"
Avoid running critical signal lines near board edges.
"
Locate the USB controller chip physically near the
USB connectors.
"
Place the STF201 near the USB connector to
restrict transient coupling.
"
Minimize the path length between the USB connec-
tor and the STF201 as well as between the USB
controller and the STF201.
"
相關PDF資料 |
PDF描述 |
|---|---|
| STF203-33.TC | Analog Miscellaneous |
| STF203-XX | Triac; Triac Type:Sensitive Gate; Peak Repetitive Off-State Voltage, Vdrm:400V; On-State RMS Current, IT(rms):4A; Gate Trigger Current (QI), Igt:3mA; Package/Case:3-TO-202; Current, It av:4A; Leaded Process Compatible:Yes |
| STB20NM60A-1 | PTC RESETTABLE 6V 1A SMD 0805 |
| STF20NM60A | Triac; Thyristor Type:Sensitive Gate; Peak Repetitive Off-State Voltage, Vdrm:400V; On State RMS Current, IT(rms):4A; Gate Trigger Current (QI), Igt:3mA; Current, It av:4A; Leaded Process Compatible:Yes; Mounting Type:Through Hole RoHS Compliant: Yes |
| STP20NM60A | Low Current Operation at 250 ，Low Reverse Leakage,Low Noise Zener Diode |
相關代理商/技術參數 |
參數描述 |
|---|---|
| STF203-33.TC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog Miscellaneous |
| STF203-33.TCT | 功能描述:IC TVS USB 33OHM RES SC70-6 RoHS:是 類別:過電壓，電流，溫度裝置 >> TVS - 其它復合 系列:- 標準包裝:1 系列:- 電壓 - 工作:120V 電壓 - 箝位:- 技術:混合技術 功率（瓦特）:- 電路數:1 應用:通用 封裝/外殼:模塊 供應商設備封裝:- 包裝:散裝 其它名稱:UAK 2-PE/S-X-120AC-STUAK2-PE/S-X-120AC-ST |
| STF203-33.TCT | 制造商:Semtech Corporation 功能描述:TRANSIENT SUPPRESSOR DIODE ARRAYBIDIREC |
| STF203-XX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:USB Upstream Port Filter & TVS for EMI Filtering and ESD Protection |
| STF2045C | 功能描述:DIODE ARRAY SCHOTTKY 45V ITO220 制造商:smc diode solutions 系列:- 包裝:管件 零件狀態:有效 二極管配置:1 對共陰極 二極管類型:肖特基 電壓 - DC 反向（Vr）（最大值）:45V 電流 - 平均整流（Io）（每二極管）:- 不同 If 時的電壓 - 正向（Vf）:580mV @ 10A 速度:快速恢復 = 200mA（Io） 反向恢復時間（trr）:- 不同?Vr 時的電流 - 反向漏電流:2mA @ 45V 安裝類型:通孔 封裝/外殼:TO-220-3 隔離片 供應商器件封裝:ITO-220AB 標準包裝:50 |
發布緊急采購，3分鐘左右您將得到回復。