- 您現在的位置：買賣IC網 > PDF目錄374929 > SSD1854U (Electronic Theatre Controls, Inc.) LCD Segment / Common Driver with Controller CMOS PDF資料下載
參數資料
| 型號： | SSD1854U |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | LCD Segment / Common Driver with Controller CMOS |
| 中文描述： | LCD段/與普通的CMOS驅動器控制器 |
| 文件頁數： | 32/48頁 |
| 文件大?。?/td> | 771K |
| 代理商： | SSD1854U |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
SSD1854
Series
Rev 1.0
08/2002
SOLOMON
27
Contrast Cruve
0
2
4
6
8
1
0
1
2
1
4
1
6
0
20
40
60
Contrast [0~63]
V
000
00
1
0
1
0
0
11
1
00
1
0
1
11
0
111
IRS
Setting
Figure 6 - Contrast Control Voltage Range Curve (TC=-0.1%/
o
C; V
DD
=2.7V; V
CI
=2.7V)
8.5
Set Power Control Register [28~2F]
This command turns on/off the various power circuits associated with the chip. All the function
blocks can be turn-on independently, but a 10ms-time must be wait between turn ON the
Regulator and Divider.
8.6
Set Display Start Line [40~43]
The second byte sent specifies which row of the RAM is to be displayed in the first row of
window defined by Set Upper/Lower Window Corner commands. Vertical window scrolling is
achieved by setting this value from 0 up to window row number + 15. The content outside the
Upper and Lower Window Row will not be affected. Refer to Page 21, example 5 for more
information.
8.7
Set Display Offset [44~47]
The second byte sent specifies the mapping of display start line (COM0 if display start line
register equals to 0) to one of ROW0-159. COM0 is mapped to ROW0 after reset.
8.8
Set Multiplex Ratio [48~4B]
This command switches default 160 multiplex modes to any multiplex from 16 to 160. The chip
pads ROW0-ROW159 will be switched to corresponding COM signal output. Examples were
given in the RAM map table. If the input value is not a number of 160, 128, 64 or 32, the higher
number of mux will be applied to the COMx pins and the RAM content of the additional lines will
be masked out from the display. Thus the actual display effect will be equal to the input value.
Suitable bias ration must be set by using Set LCD Bias command after this command is issued.
相關PDF資料 |
PDF描述 |
|---|---|
| SSD1854Z | LCD Segment / Common Driver with Controller CMOS |
| SSD1854 | LCD Segment / Common Driver with Controller CMOS |
| SSD1905 | LCD Graphics Controller CMOS |
| SSD1905QT2 | LCD Graphics Controller CMOS |
| SSF-LXH100GD-01 | T-5mm (T-1 3/4) LED, RIGHT ANGLE FAULT INDICATOR, 565nm GREEN LED, GREEN DIFFUSED LENS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SSD1854Z | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Segment / Common Driver with Controller CMOS |
| SSD1858 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Segment / Common Driver with Controller CMOS |
| SSD1858Z | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Segment / Common Driver with Controller CMOS |
| SSD1905 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Graphics Controller CMOS |
| SSD1905QT2 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Graphics Controller CMOS |
發布緊急采購，3分鐘左右您將得到回復。