- 您現在的位置：買賣IC網 > PDF目錄374929 > SSD1852Z (Electronic Theatre Controls, Inc.) LCD Segment / Common Driver With Controller CMOS PDF資料下載
參數資料
| 型號： | SSD1852Z |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | LCD Segment / Common Driver With Controller CMOS |
| 中文描述： | LCD段/與普通的CMOS驅動器控制器 |
| 文件頁數： | 32/55頁 |
| 文件大小： | 637K |
| 代理商： | SSD1852Z |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
SSD1852
Rev 1.0
01/2003
SOLOMON
27
9.13 Set PWM and FRC
This command is used to select the number of frames used in frame rate control, and the
number of levels in the pulse width modulation.
9.14 Set Segment Re-map
This command changes the mapping between the display data column address and
segment driver. It allows flexibility in layout during LCD module assembly. Refer to Figure 7.
9.15 Set Icon Enable
This command enable/disable the Icon display. When Icon display is enabled and page
address is set to Page 16. This is only one way to set the page address to 16. Therefore, when
writing data for the icon, ICONS control register ON instruction would be used to set the page
address to 16.
9.16 Set Entire Display On/Off
This command forces the entire display, including the icon row, to be “ON” regardless of
the contents of the display data RAM. This command has priority over normal/invert display. To
execute this command, Set Display On command must be sent in advance.
9.17 Set Normal/Inverse Display
This command sets the display to be either normal/inverse. In normal display, a RAM
data of 1 indicates an “ON” pixel. While in invert display, a RAM data of 0 indicates an “ON”
pixel. The icon line is not affected by this command.
9.18 Set Power Save Mode
This command is used to force the chip to enter Sleep Mode.
9.19 Start Internal Oscillator
After POR, the internal oscillator is OFF. It should be turned ON by sending this
command to the chip.
9.20 Set Display On/Off
This command turns the display on/off, by the value of the LSB.
9.21 Set Page Address
This command positions the page address to 0 to 15 possible positions in GDDRAM.
Refer to figure 7.
Set Page Address command cannot be used to set the page address to “16”. Use ICON
control register ON/OFF command to set the page address to “16”.
9.22 Set COM Output Scan Direction
This command sets the scan direction of the COM output allowing layout flexibility in LCD
module assembly.
9.23 Set Modify-Read
This command stops the automatic increment of the column address after read display
data. The column address is still automatic increment due to write display data.
相關PDF資料 |
PDF描述 |
|---|---|
| SSD1854U | LCD Segment / Common Driver with Controller CMOS |
| SSD1854Z | LCD Segment / Common Driver with Controller CMOS |
| SSD1854 | LCD Segment / Common Driver with Controller CMOS |
| SSD1905 | LCD Graphics Controller CMOS |
| SSD1905QT2 | LCD Graphics Controller CMOS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SSD1854 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Segment / Common Driver with Controller CMOS |
| SSD1854U | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Segment / Common Driver with Controller CMOS |
| SSD1854Z | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Segment / Common Driver with Controller CMOS |
| SSD1858 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Segment / Common Driver with Controller CMOS |
| SSD1858Z | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Segment / Common Driver with Controller CMOS |
發布緊急采購，3分鐘左右您將得到回復。