- 您現在的位置：買賣IC網 > PDF目錄374928 > SSD1828Z (Electronic Theatre Controls, Inc.) MOTOR LINEAR ACT 12VDC UNIPOLAR PDF資料下載
參數資料
| 型號： | SSD1828Z |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | MOTOR LINEAR ACT 12VDC UNIPOLAR |
| 中文描述： | LCD段/與普通的CMOS驅動器控制器 |
| 文件頁數： | 30/43頁 |
| 文件大?。?/td> | 434K |
| 代理商： | SSD1828Z |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
SSD1828
Rev 1.10
07/2002
SOLOMON
25
8.16 Set Frame Frequency
This command specifies the frame frequency so as to minimize the flickering due to the ac main
frequency. The frequency is set to 75Hz at 64 mux after POR.
8.17 Set Multiplex Ratio
This command switches default 64 multiplex modes to any multiplex from 16 to 64, if Icon is
disabled (POR). When Icon is set enable, the corresponding multiplex ratio setting will be
mapped to 17 to 65. The chip pads ROW0-ROW63 will be switched to corresponding COM
signal output as specified in Table 2.
8.18 Set Power Save Mode
Force the chip to enter Standby or Sleep Mode. LSB of the command will define which mode
will be entered.
8.19 Exit Power Save Mode
This command releases the chip from Sleep Mode and return to normal operation.
8.20 Set N-line Inversion
Number of line inversion is set by this command for reducing crosstalk noise. 3 to 33-line
inversion operations could be selected. At POR, this operation is disabled.
It should be noted that the total number of mux (including the icon line) should NOT be a
multiple of the inversion number (n). Or else, some lines will not change their polarity during
frame change.
8.21 Exit N-line Inversion
This command releases the chip from N-line inversion mode. The driving waveform will be
inverted once per frame after issuing this command.
8.22 Set DC-DC Converter Factor
Internal DC-DC converter factor is set by this command. For SSD1828, 2X to 5X multiplying
factors could be selected. 2X to 5X factors are selected using this command.
8.23 Set Icon Enable
This command enable/disable the Icon displays.
8.24 Start Internal Oscillator
After POR, the internal oscillator is OFF. It should be turned ON by sending this command to
the chip.
8.25 Set Display Data Length
This two-bytes command only valid when 3-wire SPI configuration is set by H/W input
(PS0=PS1=L). The second 8-bit is used to indicate that a specified number display data byte(s)
(1-256) are to be transmitted. Next byte after the display data string is handled as a command.
8.26 Set Test Mode
This command forces the driver chip into its test mode for internal testing of the chip. Under
normal operation, user should NOT use this command.
相關PDF資料 |
PDF描述 |
|---|---|
| SSD1828 | LCD Segment / Common Driver with Controller CMOS |
| SSD1852 | LCD Segment / Common Driver With Controller CMOS |
| SSD1852T2R1 | LCD Segment / Common Driver With Controller CMOS |
| SSD1852TR1 | LCD Segment / Common Driver With Controller CMOS |
| SSD1852Z | LCD Segment / Common Driver With Controller CMOS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SSD1850 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CMOS LCD Segment / Common Driver with Controller |
| SSD1850Z | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CMOS LCD Segment / Common Driver with Controller |
| SSD1851 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CMOS LCD Segment / Common Driver with Controller |
| SSD1851TR1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CMOS LCD Segment / Common Driver with Controller |
| SSD1851U | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CMOS LCD Segment / Common Driver with Controller |
發布緊急采購，3分鐘左右您將得到回復。