- 您現在的位置：買賣IC網 > PDF目錄374928 > SSD1800 (Electronic Theatre Controls, Inc.) LCD Segment / Common Driver with Controller PDF資料下載
參數資料
| 型號： | SSD1800 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | LCD Segment / Common Driver with Controller |
| 中文描述： | LCD段/驅動器與控制器通用 |
| 文件頁數： | 29/42頁 |
| 文件大?。?/td> | 598K |
| 代理商： | SSD1800 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
SSD1800 Series
Rev 1.0
P 29/42 Mar 2004
Solomon Systech
12.3 Set Power Save Mode / Oscillator Control
To enter Standby or Sleep Mode, it should be done by turning off the internal oscillator and turning on the power
save control bit. The corresponding control bits are X
1
X
0
= 01. In order to put the system into low power consumption
mode, internal voltage converter, voltage regulator and voltage divider should also be turned off by using Power
Control Register. After putting the system into power save mode, the following status will be entered:
1. Internal oscillator and LCD power supply circuits are stopped.
2. Segment and Common drivers output AV
SS
level.
3. The display data and operation mode before sleep are held. All the internal circuit is stopped.
12.4 Function Set
This command sets 2 functions on the system. They are COM shift direction (left or right) and CGROM/ CGRAM
character area select.
12.5 Set Display Start Line
This command is to set Display Start Line register to determine starting address of display data RAM to be
displayed by selecting a value from 0 to 3. With the value equals to 0, the display will start from address (00h-0Fh).
With the value equals to 1, the display will start from address (10h-1Fh). With the value equals to 2, the display will
start from address (20h-2Fh). With the value equals to 3, the display will start from address (30-3Fh).
12.6 Set Bias Control
Bias ratio 1/4 or 1/5 could be set using this command. When changing the number of line display, the bias ratio
also needs to be adjusted to make display contrast consistent.
12.7 Set Power Control Register
This command turns on / off the various power circuits associated with the chip which including regulated DC-DC
converter and voltage divider.
12.8 Set Display Control
This command provides 3 display functions. It turns on/off of the cursor, blink and display. When both cursor and
blink control bit set high, the driver make LCD alternate between inverting display character and normal display
character at the cursor position with about a half second. On the contrary, if cursor control bit is low, only a normal
character is displayed regardless of blink control bit.
相關PDF資料 |
PDF描述 |
|---|---|
| SSD1800AV | LCD Segment / Common Driver with Controller |
| SSD1800Z | LCD Segment / Common Driver with Controller |
| SSD1801 | LCD Segment / Common Driver with Controller for Character Display System |
| SSD1801AV | LCD Segment / Common Driver with Controller for Character Display System |
| SSD1801Z | LCD Segment / Common Driver with Controller for Character Display System |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SSD1800AV | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Segment / Common Driver with Controller |
| SSD1800Z | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Segment / Common Driver with Controller |
| SSD1801 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Segment / Common Driver with Controller for Character Display System |
| SSD1801AV | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Segment / Common Driver with Controller for Character Display System |
| SSD1801Z | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Segment / Common Driver with Controller for Character Display System |
發布緊急采購，3分鐘左右您將得到回復。