- 您現在的位置：買賣IC網 > PDF目錄374854 > SN54LS162J (ON SEMICONDUCTOR) BCD DECADE COUNTERS/ 4-BIT BINARY COUNTERS PDF資料下載
參數資料
| 型號： | SN54LS162J |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 通用總線功能 |
| 英文描述： | BCD DECADE COUNTERS/ 4-BIT BINARY COUNTERS |
| 中文描述： | BCD碼十年計數器/ 4位二進制計數器 |
| 文件頁數： | 2/6頁 |
| 文件大小： | 79K |
| 代理商： | SN54LS162J |
*For the LS162A and
*
LS163A only.
H = HIGH Voltage Level
L = LOW Voltage Level
X = Don’t Care
5-2
FAST AND LS TTL DATA
SN54/74LS160A
SN54/74LS161A
SN54/74LS162A
SN54/74LS163A
STATE DIAGRAM
LS160A
LS162A
LS161A
LS163A
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
NOTE:
The LS160A and LS162A can be preset to any state,
but will not count beyond 9. If preset to state 10, 11,
12, 13, 14, or 15, it will return to its normal sequence
within two clock pulses.
LOGIC EQUATIONS
Count Enable = CEP
CET
PE
TC for LS160A & LS162A = CET
Q0
Q1
Q2
Q3
TC for LS161A & LS163A = CET
Q0
Q1
Q2
Q3
Preset = PE
CP + (rising clock edge)
Reset = MR (LS160A & LS161A)
Reset = SR
CP + (rising clock edge)
Reset =
(LS162A & LS163A)
FUNCTIONAL DESCRIPTION
The LS160A/161A/162A/163A are 4-bit synchronous
counters with a synchronous Parallel Enable (Load) feature.
The counters consist of four edge-triggered D flip-flops with
the appropriate data routing networks feeding the D inputs. All
changes of the Q outputs (except due to the asynchronous
Master Reset in the LS160A and LS161A) occur as a result of,
and synchronous with, the LOW to HIGH transition of the
Clock input (CP). As long as the set-up time requirements are
met, there are no special timing or activity constraints on any
of the mode control or data inputs.
Three control inputs — Parallel Enable (PE), Count Enable
Parallel (CEP) and Count Enable Trickle (CET) — select the
mode of operation as shown in the tables below. The Count
Mode is enabled when the CEP, CET, and PE inputs are HIGH.
When the PE is LOW, the counters will synchronously load the
data from the parallel inputs into the flip-flops on the LOW to
HIGH transition of the clock. Either the CEP or CET can be
used to inhibit the count sequence. With the PE held HIGH, a
LOW on either the CEP or CET inputs at least one set-up time
prior to the LOW to HIGH clock transition will cause the
existing output states to be retained. The AND feature of the
two Count Enable inputs (CET
CEP) allows synchronous
cascading without external gating and without delay accu-
mulation over any practical number of bits or digits.
The Terminal Count (TC) output is HIGH when the Count
Enable Trickle (CET) input is HIGH while the counter is in its
maximum count state (HLLH for the BCD counters, HHHH for
the Binary counters). Note that TC is fully decoded and will,
therefore, be HIGH only for one count state.
The LS160A and LS162A count modulo 10 following a
binary coded decimal (BCD) sequence. They generate a TC
output when the CET input is HIGH while the counter is in state
9 (HLLH). From this state they increment to state 0 (LLLL). If
loaded with a code in excess of 9 they return to their legitimate
sequence within two counts, as explained in the state
diagram. States 10 through 15 do not generate a TC output.
The LS161A and LS163A count modulo 16 following a
binary sequence. They generate a TC when the CET input is
HIGH while the counter is in state 15 (HHHH). From this state
they increment to state 0 (LLLL).
The Master Reset (MR) of the LS160A and LS161A is
asynchronous. When the MR is LOW, it overrides all other
input conditions and sets the outputs LOW. The MR pin should
never be left open. If not used, the MR pin should be tied
through a resistor to VCC, or to a gate output which is
permanently set to a HIGH logic level.
The active LOW Synchronous Reset (SR) input of the
LS162A and LS163A acts as an edge-triggered control input,
overriding CET, CEP and PE, and resetting the four counter
flip-flops on the LOW to HIGH transition of the clock. This
simplifies the design from race-free logic controlled reset
circuits, e.g., to reset the counter synchronously after
reaching a predetermined value.
MODE SELECT TABLE
*SR
PE
CET
CEP
Action on the Rising Clock Edge ( )
L
H
H
H
H
X
L
H
H
H
X
X
H
L
X
X
X
H
X
L
RESET (Clear)
LOAD (Pn
→
Qn)
COUNT (Increment)
NO CHANGE (Hold)
NO CHANGE (Hold)
相關PDF資料 |
PDF描述 |
|---|---|
| SN54LS163J | BCD DECADE COUNTERS/ 4-BIT BINARY COUNTERS |
| SN74LS160D | Reference Design kit for ADNS-3040 |
| SN74LS160N | Reference Design kit for ADNS-5030 |
| SN74LS161D | Reference Design kit for ADNS-5020-EN |
| SN74LS161N | LED-based, Low Power, Small Form Factor Optical Mouse Sensor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SN54LS162W | 制造商:Texas Instruments 功能描述: |
| SN54LS163AJ | 制造商:Texas Instruments 功能描述:Counter Single 4-Bit Sync Binary UP 16-Pin CDIP Tube 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Texas Instruments 功能描述:SYNC 4-BIT BINARY COUNTER - Rail/Tube 制造商:Motorola Inc 功能描述:Counter, Up, 4 Bit Binary, 16 Pin, Ceramic, DIP |
| SN54LS164J | 制造商:Texas Instruments 功能描述:Shift Register Single 8-Bit Serial to Parallel 14-Pin CDIP Tube 制造商:Texas Instruments 功能描述:SHIFT REGISTER SGL 8BIT SERL TO PARALLEL 14CDIP - Rail/Tube |
| SN54LS165AJ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述: 制造商:Texas Instruments 功能描述:8-BIT PISO SHIFT REGISTER - Rail/Tube 制造商:Texas Instruments 功能描述:Shift Register Single 8-Bit Serial/Parallel to Serial 16-Pin CDIP Tube |
| SN54LS165J | 制造商:Texas Instruments 功能描述: 制造商:Texas Instruments 功能描述:Shift Register, 16 Pin, Ceramic, DIP |
發布緊急采購，3分鐘左右您將得到回復。