參數資料
型號： SMH4042ASAGN
廠商： Electronic Theatre Controls, Inc.
元件分類： 基準電壓源/電流源
英文描述： Distributed Power Hot-Swap Controller for CompactPCI
中文描述： 分布式電源熱插拔控制器的CompactPCI
文件頁數： 12/28頁
文件大?。?/td> 1822K
代理商： SMH4042ASAGN
12
SMH4042A
2070 9.1 5/27/03
SUMMIT MICROELECTRONICS, Inc.
Start and Stop Conditions
Both Data and Clock lines remain high when the bus is not
busy. Data transfer between devices may be initiated with
a Start condition only when SCL and SDA are high. A high-
to-low transition of the Data line while the Clock line is high
is defined as a Start condition. A low-to-high transition of
the Data line while the Clock line is high is defined as a
Stop condition. See Figure 6.
Protocol
The protocol defines any device that sends data onto the
bus as a Transmitter, and any device that receives data
as a Receiver. The device controlling data transmission
is called the Master, and the controlled device is called
the Slave. In all cases the Summit Microelectronic
devices are Slave devices, since they never initiate any
data transfers.
Acknowledge
Data is always transferred in 8-Bit bytes. Acknowledge
(ACK) is used to indicate a successful data transfer. The
Transmitting device will release the bus after transmitting
eight bits. During the ninth clock cycle the Receiver will
pull the SDA line low to Acknowledge that it received the
eight bits of data (See Figure 7). The termination of a
Master Read sequence is indicated by a non-Acknowl-
edge (NACK), where the Master will leave the Data line
high.
In the case of a Read from a Summit part, when the last
byte has been transferred to the Master, the Master will
leave the Data line high for a NACK. This will cause the
Summit part to stop sending data, and the Master will
issue a Stop on the clock pulse following the NACK.
In the case of a Write to a Summit part the Master will send
a Stop on the clock pulse after the last Acknowledge. This
will indicate to the Summit part that it should begin its
internal non-volatile write cycle.
Basic Read and Write
The first byte from a Master is always made up of a seven
bit Slave address and the Read/Write bit. The R/W bit tells
the Slave whether the Master is reading data from the bus
or writing data to the bus (1 = Read, 0 = Write). The first
four of the seven address bits are called the Device Type
Identifier (DTI). The DTI for the SMH4042A is 1010
BIN
. The
next two bits are used to select one-of-four possible
devices on the bus. The next bit is the block select bit.
The SMH4042A will issue an Acknowledge after recogniz-
ing a Start condition and its DTI.
In the Read mode the SMH4042A transmits eight bits of
data, then releases the SDA line, and monitors the line for
an Acknowledge signal. If an Acknowledge is detected,
and no Stop condition is generated by the Master, the
SMH4042A will continue to transmit data. If an Acknowl-
edge is not detected (NACK), the SMH4042A will terminate
further data transmission. See Figure 9.
In the Write mode the SMH4042A receives eight bits of
data, then generates an Acknowledge signal. It will
continue to generate ACKs until a Stop condition is
generated by the Master. See Figure 10.
Figure 6. I
2
C Start and Stop Timing
Figure 7. Acknowledge Timing
Figure 8. Typical Master Address Byte Transmission
2070 Fig06
SCL
SDA In
START
Condition
STOP
Condition
SCL
SDA
Trans
SDA
Rec
1
2
3
8
9
ACK
2070 Fig07
SCL
SDA
1
2
3
8
9
4
5
6
7
1
0
1
R/W
0
x
x
x
ACK
2070 Fig08
相關PDF資料
PDF描述
SMH4042AGBKN Distributed Power Hot-Swap Controller for CompactPCI
SMH4042AGBGM Aluminum Polymer SMT Capacitor; Capacitance: 82uF; Voltage: 6.3V; Case Size: 10x12.7 mm; Packaging: Tape & Reel
SMH4042AGBGN Aluminum Polymer SMT Capacitor; Capacitance: 120uF; Voltage: 10V; Case Size: 8x7 mm; Packaging: Tape & Reel
SMH4042AGBHM Aluminum Polymer SMT Capacitor; Capacitance: 150uF; Voltage: 10V; Case Size: 10x8 mm; Packaging: Tape & Reel
SMH4042AGBKM Aluminum Polymer SMT Capacitor; Capacitance: 470uF; Voltage: 6.3V; Case Size: 8x7 mm; Packaging: Tape & Reel
相關代理商/技術參數
參數描述
SMH4042ASAHM 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Distributed Power Hot-Swap Controller for CompactPCI
SMH4042ASAHN 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Distributed Power Hot-Swap Controller for CompactPCI
SMH4042ASAKM 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Distributed Power Hot-Swap Controller for CompactPCI
SMH4042ASAKN 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Distributed Power Hot-Swap Controller for CompactPCI
SMH4042ASALM 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Distributed Power Hot-Swap Controller for CompactPCI
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*