- 您現在的位置：買賣IC網 > PDF目錄374842 > SMH4042AGBKM (Electronic Theatre Controls, Inc.) Aluminum Polymer SMT Capacitor; Capacitance: 470uF; Voltage: 6.3V; Case Size: 8x7 mm; Packaging: Tape & Reel PDF資料下載
參數資料
| 型號： | SMH4042AGBKM |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Aluminum Polymer SMT Capacitor; Capacitance: 470uF; Voltage: 6.3V; Case Size: 8x7 mm; Packaging: Tape & Reel |
| 中文描述： | 分布式電源熱插拔控制器的CompactPCI |
| 文件頁數： | 20/28頁 |
| 文件大?。?/td> | 1822K |
| 代理商： | SMH4042AGBKM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
20
SMH4042A
2070 9.1 5/27/03
SUMMIT MICROELECTRONICS, Inc.
I/O Pre-charge
The
CompactPCI
specs require the add-in board to pre-
charge the board’s I/Os before making contact with bus
pins, and sets the pre-charge voltage at 1V ±0.1V. The
SMH4042A provides an accurate 1V reference output that
SPECIAL CONSIDERATIONS
The example application shown in Figure 11 shows both
of the BD_SEL inputs being used independently. These
two inputs are effectively ANDed internally and they must
both be low before any sequencing will proceed. In most
design cases the BD_SEL1# connection to an injector
switch is redundant and realistically can be grounded.
The
CompactPCI
Hot Swap specification does provide a
mechanism for implementing high availability systems
using “Full Hot Swap” boards. This capability entails
integrating the injector/ejector handle, the blue LED and
a board status signal. Section 2.3.2 of the
CompactPCI
Hot Swap specification states the following.
host that either a board has been freshly inserted or is
about to be extracted.”
“A signal (ENUM#) is provided to notify the system
the board, is used to signal the insertion or impending
extraction of a board.”
“A switch, actuated with the lower ejector handle of
is accurate and stable prior to the medium length pins
making contact. The 1VREF output should be the
reference input to a unity gain op amp circuit. Figure 17
is a typical implementation utilizing a common op amp.
Figure 17. I/O Pre-charge Circuit
it is permissible to extract a board.”
“A blue LED, located on the board is illuminated when
Figure 18 illustrates a possible implementation of the
circuits needed. It should be noted this will require a
status register that works in conjunction with the switch
logic to generate the ENUM# signal. Notice the blue LED
circuit and the active high reset output used to activate a
current boost circuit for the LED. The sequence of
operations is as follows:
The long pins engage.
the BD_SEL pull-up resistor.
Power is supplied to the SMH4042A, the LED and
dependent upon the interface operating levels.
V(I/O) is either the early 5V or the early 3V,
going low.
The LED is illuminated by LOCAL_PCI_RST#
+
–
LMV321
2070 Fig17
V
CC
5
1V
REF
SMH4042A
Resistor Array
T
B
Early Power
T
B
相關PDF資料 |
PDF描述 |
|---|---|
| SMH4042AGBLM | Distributed Power Hot-Swap Controller for CompactPCI |
| SMH4042AGBLN | TERM 5"7 TS GRAPH. BLUE MODE OPT.VERS. |
| SMH4042ASAHM | TERM 5"7 TS GRAPH. MONO LOW END VERS. |
| SMH4042ASAHN | TERM 5"7 TS GRAPH. MONO STD. VERS. |
| SMH4042ASAKM | TERM.5"7 TS GRAPH. C.STN LOW END VERS. |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SMH4042AGBKN | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Distributed Power Hot-Swap Controller for CompactPCI |
| SMH4042AGBLM | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Distributed Power Hot-Swap Controller for CompactPCI |
| SMH4042AGBLN | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Distributed Power Hot-Swap Controller for CompactPCI |
| SMH4042ASAGM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Distributed Power Hot-Swap Controller for CompactPCI |
| SMH4042ASAGN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Distributed Power Hot-Swap Controller for CompactPCI |
發(fā)布緊急采購，3分鐘左右您將得到回復。