- 您現在的位置：買賣IC網 > PDF目錄11824 > SC28L91A1A,512 (NXP Semiconductors)IC UART SINGLE W/FIFO 44-PLCC PDF資料下載
參數資料
| 型號： | SC28L91A1A,512 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 2/30頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART SINGLE W/FIFO 44-PLCC |
| 標準包裝： | 26 |
| 系列： | IMPACT |
| 特點： | 故障啟動位檢測 |
| 通道數： | 1，UART |
| FIFO's： | 16 字節 |
| 電源電壓： | 3.3V，5V |
| 帶自動流量控制功能： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 供應商設備封裝： | 44-PLCC |
| 包裝： | 管件 |
| 其它名稱： | 935267418512 SC28L91A1A SC28L91A1A-ND |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
Philips Semiconductors
Product data sheet
SC28L91
3.3 V or 5.0 V Universal Asynchronous
Receiver/Transmitter (UART)
2004 Oct 21
10
ABSOLUTE MAXIMUM RATINGS1
Symbol
Parameter
Rating
Unit
Tamb
Operating ambient temperature range2
Note 4
°C
Tstg
Storage temperature range
–65 to +150
°C
VCC
Voltage from VCC to GND3
–0.5 to +7.0
V
VS
Voltage from any pin to GND3
–0.5 to VCC +0.5
V
PD
Package power dissipation (PLCC44)
2.4
W
PD
Package power dissipation (PQFP44)
1.78
W
Derating factor above 25
°C (PLCC44)
19
mW/
°C
Derating factor above 25
°C (PQFP44)
14
mW/
°C
NOTES:
1. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any other condition above those indicated in the operation section of this specification is not
implied.
2. For operating at elevated temperatures, the device must be derated based on +150
°C maximum junction temperature.
3. This product includes circuitry specifically designed for the protection of its internal devices from damaging effects of excessive static
charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying any voltages larger than the rated maxima.
4. Parameters are valid over specified temperature and voltage range.
DC ELECTRICAL CHARACTERISTICS1, 2, 3
VCC = 5 V ± 10 %, Tamb = –40 °C to +85 °C, unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VIL
Input low voltage
0.8
V
VIH
Input high voltage (except X1/CLK)
2.4
1.5
V
VIH
Input high voltage (X1/CLK)
0.8VCC
2.4
V
VOL
Output low voltage
IOL = 2.4 mA
0.2
0.4
V
VOH
Output high voltage (except OD outputs)4
IOH = –400 A
VCC – 0.5
V
IIX1PD
X1/CLK input current - power down
VIN = 0 V to VCC
0.5
0.05
0.5
A
IILX1
X1/CLK input low current - operating
VIN = 0 V
–130
0
A
IIHX1
X1/CLK input high current - operating
VIN = VCC
0
130
A
Input leakage current:
II
All except input port pins
VIN = 0 V to VCC
–0.5
0.05
+0.5
A
Input port pins5
VIN = 0 V to VCC
–8
0.05
+0.5
A
IOZH
Output off current high, 3-State data bus
VIN = VCC
0.5
A
IOZL
Output off current low, 3-State data bus
VIN = 0 V
–0.5
A
IODL
Open-drain output low current in off-state
VIN = 0 V
–0.5
A
IODH
Open-drain output high current in off-state
VIN = VCC
0.5
A
Power supply current6
ICC
Operating mode
CMOS input levels
7
25
mA
Power down mode
CMOS input levels
≤1
5
mA
NOTES:
1. Parameters are valid over specified temperature and voltage range.
2. All voltage measurements are referenced to ground (GND). For testing, all inputs swing between 0.4 V and 3.0 V with a transition time of
5 ns maximum. For X1/CLK, this swing is between 0.4 V and 0.8VCC. All time measurements are referenced at input voltages of 0.8 V and
2.0 V and output voltages of 0.8 V and 2.0 V, as appropriate.
3. Typical values are at +25
°C, typical supply voltages, and typical processing parameters.
4. Test conditions for outputs: CL = 125 pF, except open drain outputs. Test conditions for open drain outputs: CL = 125 pF,
constant current source = 2.6 mA.
5. Input port pins have active pull-up transistors that will source a typical 2
A from VCC when the input pins are at VSS.
Input port pins at VCC source 0.0 A.
6. All outputs are disconnected. Inputs are switching between CMOS levels of VCC – 0.2 V and VSS + 0.2 V.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-26B-IY | CONVERTER MOD DC/DC 95V 50W |
| D38999/20JB98HN | CONN RCPT 6POS WALL MNT W/PINS |
| VE-BT2-IX-F3 | CONVERTER MOD DC/DC 15V 75W |
| SC26C92C1B,528 | IC UART DUAL W/FIFO 44PQFP |
| VI-24Z-IX | CONVERTER MOD DC/DC 2V 30W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC28L91A1A-S | 功能描述:UART 接口集成電路 3V-5V 1CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC28L91A1A-T | 功能描述:UART 接口集成電路 3V-5V 1CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC28L91A1B | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:3.3V-5.0V Universal Asynchronous Receiver/Transmitter (UART) |
| SC28L91A1B,528 | 功能描述:UART 接口集成電路 3V-5V 1CH UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC28L91A1B,551 | 功能描述:UART 接口集成電路 UART SINGLE W/FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。