參數資料
型號： SC16C752IB48,157
廠商： NXP Semiconductors
文件頁數： 4/47頁
文件大?。?/td> 0K
描述： IC DUAL UART 64BYTE 48LQFP
標準包裝： 1,250
通道數： 2，DUART
FIFO's： 64 字節
電源電壓： 2.5V，3.3V，5V
帶自動流量控制功能： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
安裝類型： 表面貼裝
封裝/外殼： 48-LQFP
供應商設備封裝： 48-LQFP（7x7）
包裝： 托盤
其它名稱： 935270055157
SC16C752IB48
SC16C752IB48-ND
Philips Semiconductors
SC16C752
Dual UART with 64-byte FIFO
Product data
Rev. 04 — 20 June 2003
12 of 47
9397 750 11635
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
6.5 Interrupts
The SC16C752 has interrupt generation and prioritization (six prioritized levels of
interrupts) capability. The interrupt enable register (IER) enables each of the six types
of interrupts and the INT signal in response to an interrupt generation. The IER can
also disable the interrupt system by clearing bits 0-3, 5-7. When an interrupt is
generated, the IIR indicates that an interrupt is pending and provides the type of
interrupt through IIR[5;0]. Table 6 summarizes the interrupt control functions.
It is important to note that for the framing error, parity error, and break conditions,
LSR[7] generates the interrupt. LSR[7] is set when there is an error anywhere in the
RX FIFO, and is cleared only when there are no more errors remaining in the FIFO.
LSR[4:2] always represent the error status for the received character at the top of the
RX FIFO. Reading the RX FIFO updates LSR[4:2] to the appropriate status for the
new character at the top of the FIFO. If the RX FIFO is empty, then LSR[4:2] are all
zeros.
For the Xoff interrupt, if an Xoff ow character detection caused the interrupt, the
interrupt is cleared by an Xon ow character detection. If a special character
detection caused the interrupt, the interrupt is cleared by a read of the LSR.
Table 6:
Interrupt control functions
IIR[5:0]
Priority
level
Interrupt type
Interrupt source
Interrupt reset method
000001
None
none
000110
1
receiver line status
OE, FE, PE, or BI errors occur in
characters in the RX FIFO
FE, PE, BI: all erroneous
characters are read from the
RX FIFO.
OE: read LSR
001100
2
RX time-out
stale data in RX FIFO
read RHR
000100
2
RHR interrupt
DRDY (data ready)
(FIFO disable)
RX FIFO above trigger level
(FIFO enable)
read RHR
000010
3
THR interrupt
TFE (THR empty)
(FIFO disable)
TX FIFO passes above trigger level
(FIFO enable)
read IIR or a write to the THR
000000
4
modem status
MSR[3:0] = 0
read MSR
010000
5
Xoff interrupt
receive Xoff character(s)/special
character
receive Xon character(s)/Read of
IIR
100000
6
CTS, RTS
RTS pin or CTS pin change state from
active (LOW) to inactive (HIGH)
read IIR
相關PDF資料
PDF描述
ATMEGA1284P-AUR MCU AVR 128KB FLASH 20MHZ 44TQFP
ATMEGA1284P-MUR MCU AVR 128KB FLASH 20MHZ 44VQFN
AT89C51RB2-SLRUM MCU 8051 16K FLASH 5V 44-PLCC
AT89C51RB2-SLRUL MCU 8051 16K FLASH 3V 44-PLCC
MS27484E14B18S CONN PLUG 18POS STRAIGHT W/SCKT
相關代理商/技術參數
參數描述
SC16C754 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Quad UART with 64-byte FIFO
SC16C754B 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs
SC16C754BIA68 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C754BIA68,512 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C754BIA68,518 功能描述:UART 接口集成電路 4CH. UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*