參數資料
型號： S29GL256N80FAI010
廠商： SPANSION LLC
元件分類： PROM
英文描述： MirrorBit Flash Family
中文描述： 16M X 16 FLASH 3V PROM, 80 ns, PBGA64
封裝： 13 X 11 MM, 1MM PITCH, FBGA-64
文件頁數： 80/110頁
文件大?。?/td> 2624K
代理商： S29GL256N80FAI010
May 13, 2004 27631A4
S29GLxxxN MirrorBitTM Flash Family
71
Ad va nc e
Inform ati o n
Reads and writes from the main memory are allowed.
PPB Lock Bit Set Command
The PPB Lock Bit Set command is used to set the PPB Lock Bit to the “freeze state”
if it is cleared either at reset or if the Password Unlock command was successfully
executed. There is no PPB Lock Bit Clear command. Once the PPB Lock Bit is set
to the “freeze state”, it cannot be cleared unless the device is taken through a
power-on clear (for Persistent Protection Mode) or the Password Unlock command
is executed (for Password Protection Mode). If the Password Protection Mode Lock
Bit is programmed, the PPB Lock Bit status is reflected as set to the “freeze state”,
even after a power-on reset cycle.
PPB Lock Bit Status Read Command
The programming state of the PPB Lock Bit can be verified by executing a PPB
Lock Bit Status Read command to the device.
The Global Volatile Sector Protection Freeze Command Set Exit command
must be issued after the execution of the commands listed previously to reset the
device to read mode.
Volatile Sector Protection Command Set
The Volatile Sector Protection Command Set permits the user to set the Dynamic
Protection Bit (DYB) to the “protected state”, clear the Dynamic Protection Bit
(DYB) to the “unprotected state”, and read the logic state of the Dynamic Protec-
tion Bit (DYB).
The Volatile Sector Protection Command Set Entry command sequence
must be issued prior to any of the commands listed following to enable proper
command execution.
Note that issuing the Volatile Sector Protection Command Set Entry com-
mand disables reads for the bank selected with the command. Reads and
Writes for other banks excluding that bank are allowed.
DYB Set Command
DYB Clear Command
The DYB Set and DYB Clear commands are used to protect or unprotect a DYB for
a given sector. The high order address bits are issued at the same time as the
code 00h or 01h on DQ7-DQ0. All other DQ data bus pins are ignored during the
data write cycle. The DYB bits are modifiable at any time, regardless of the state
of the PPB bit or PPB Lock Bit. The DYB bits are cleared to the “unprotected state”
at power-up or hardware reset.
—DYB Status Read Command
The programming state of the DYB bit for a given sector can be verified by writing
a DYB Status Read command to the device. This requires an initial access delay.
The Volatile Sector Protection Command Set Exit command must be issued
after the execution of the commands listed previously to reset the device to read
mode.
Note that issuing the Volatile Sector Protection Command Set Exit com-
mand re-enables reads and writes to the main memory.
SecSi Sector Entry Command
The SecSi Sector Entry command allows the following commands to be executed
Read from SecSi Sector
相關PDF資料
PDF描述
S29GL256N80FFI010 MirrorBit Flash Family
S29GL256N80FFI013 MirrorBit Flash Family
S29JL032H90TAI223 2M X 16 FLASH 3V PROM, 90 ns, PDSO48
S29WS064N0PBAW011 256/128/64 MEGABIT CMOS 1.8 VOLT ONLY SIMULTANEOUS READ/WRITE BURST MODE FLASH MEMORY
S29WS128N0LBFI111 256/128/64 MEGABIT CMOS 1.8 VOLT ONLY SIMULTANEOUS READ/WRITE BURST MODE FLASH MEMORY
相關代理商/技術參數
參數描述
S29GL256N90FFIR10 制造商:Spansion 功能描述:Flash Mem Parallel 3.3V 256M-Bit 32M x 8/16M x 16 90ns 64-Pin Fortified BGA Tray
S29GL256N90FFIR22 制造商:Spansion 功能描述:
S29GL256N90TFIR10 制造商:Spansion 功能描述:NOR Flash Parallel 3.3V 256Mbit 32M/16M x 8bit/16bit 90ns 56-Pin TSOP Tray 制造商:Spansion 功能描述:Flash - NOR IC
S29GL256N90TFIR2 制造商:Spansion 功能描述:
S29GL256N90TFIR20 制造商:Spansion 功能描述:Flash Mem Parallel 3.3V 256M-Bit 32M x 8/16M x 16 90ns 56-Pin TSOP Tray 制造商:Spansion 功能描述:Flash - NOR IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*